- 您現在的位置：買賣IC網 > PDF目錄370442 > HC5520CM (Harris Corporation) CO/PABX Polarity Reversal Subscriber Line Interface Circuit PDF資料下載
參數資料
| 型號： | HC5520CM |
| 廠商： | Harris Corporation |
| 英文描述： | CO/PABX Polarity Reversal Subscriber Line Interface Circuit |
| 中文描述： | 二氧化碳/極性反轉交換機用戶線接口電路 |
| 文件頁數： | 6/20頁 |
| 文件大?。?/td> | 191K |
| 代理商： | HC5520CM |
6
Circuit Operation and Design Information
The HC5520 is a current feed voltage sense
S
ubscriber
L
ine
I
nterface
C
ircuit (SLIC). It provides extensive digitally con-
trolled supervisory functions, DC loop feed functions, and
user selectable 2 wire impedance matching functions.
Modes of Operation
The HC5520 has seven possible modes of operation. These
modes of operation are either controlled by the digital control
inputs to the SLIC or controlled by the loop status output of
the SLIC. The modes of operation and the function of the
digital control inputs are given in Table 1.
Normal Loop Feed Mode
When PDI = 1, setting the PRI to a logic “1” places the SLIC
in the Normal Loop Feed mode. This is the normal opera-
tional mode of the SLIC. With a nominal battery supply of -
48V and an on-hook condition, the voltage at the Tip termi-
nal will be approximately 8% of the battery supply voltage. In
this case the Tip voltage is about -3.8V. Similarly, the voltage
at the Ring terminal will be approximately 92% of the battery
supply voltage or about -44.2V.
In the Normal mode the Tip voltage is more positive than
the Ring voltage; therefore, in an off-hook condition, the DC
loop current flows from Tip to Ring. The loop feeding
characteristics will be given in the battery feed section. All of
the specifications applicable to this mode of operation are
provided in the electrical specifications portion of the
HC5520 data sheet.
Reverse Loop Feed Mode
When PDI = 1, setting the PRI to a logic “0” places the SLIC
in the Reverse Loop Feed mode. In this mode, the Ring ter-
minal voltage is more positive than the Tip terminal voltage.
Thus, in an off-hook condition, the DC loop current flows
from Ring to Tip. The loop feeding characteristics in the
Reverse mode are the same as in the Normal mode. All of
the specifications applicable to this mode of operation are
provided in the electrical specifications portion of the
HC5520 data sheet.
Battery Feed
The HC5520 is designed to provide a 300
resistive feed
(150
per wire) for long loop applications. It will supply a DC
loop feed current of 18mA into an 1800
loop at the nominal
battery supply of -48V. At shorter loop lengths or higher bat-
tery supply voltages, the DC feed is current-limited to nomi-
nally 26mA in order to conserve power. For internal chip
power management purposes, external power sharing resis-
tors are used to provide some of the DC loop current. This
allows a substantial amount of the power to be dissipated off
the chip, particularly in short loop applications. A typical loop
feeding characteristic for Normal and Reverse Loop Feed
Modes of operation is shown in Figure 1.
Loop Supervision - Switch Hook Detection
The Loop Supervision circuit operates in the Normal and
Reverse Loop Feed modes. The DC loop current is moni-
tored and the off-hook condition is indicated when the loop
resistance is less than 2.4k
. When this occurs, the SHDO
output will be set to a logic low in order to signal the system
that an off-hook condition exists. If the subscriber is using a
rotary dial telephone, the system can monitor the dial pulses
through the SHDO output.
Ringing - Ring Trip Detection Mode
The ringing voltage is cadenced to a subscriber loop by
applying a logic signal to the Rci input. When a logic “0” is
received at the RCI input, the HC5520 will set the RD output
to low and thus pull current through the ring relay coil and
energize the ring relay. This causes the subscriber’s tele-
phone to begin ringing. At this time the ringing current
through the ring ballast resistor is monitored to determine
whether an off-hook condition is present. Once the sub-
scriber goes off-hook, the ring trip circuit will turn off the ring
relay after the next occurrence of a zero net current flow
through the ring ballast resistor. At the same time, the SHDO
output will be set to a logic low to indicate the ring trip detec-
TABLE 1.
OPERATION
MODE
SLIC
FUNCTION
CONTROL
INPUTS
Normal
Loop Feed
Normal
Normal
PRI = High
Reverse
Loop Feed
Reverse
Normal
PRI = Low
Loop
Powerdown
P’down
Loop
power down
PDI = Low
Ringing
Ringing
Ring trip
detection only
RCI = Low
Test out
Test-out
Normal
TAI = Low
Test in
Test-in
Normal
TBI = Low
Thermal
Shut Down
TSD
Loop
Powerdown
I
LOOP
R
LOOP
600
800 1.0K 1.2K 1.4K 1.6K 1.8K 2.0K 2.2K 2.4K
10
20
30
FIGURE 1. BATTERY FEED CHARACTERISTICS
m
HC5520
相關PDF資料 |
PDF描述 |
|---|---|
| HC5520CQ | CO/PABX Polarity Reversal Subscriber Line Interface Circuit |
| HC594 | 8-BIT SHIFT REGISTERS WITH OUTPUT REGISTERS |
| HC595M | 8-BIT SHIFT REGISTERS WITH 3-STATE OUTPUT REGISTERS |
| HC74HC444 | Quad. Tridirectional Bus Transceiver(with noninverted/inverted 3-state outputs) |
| HC79 | MEDIUM/HIGH VOLTAGE MULTILAYER CERAMIC CAPACITORS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HC5520CQ | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| HC5521 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:SLIC Subscriber Line Interface Circuit |
| HC5521CM | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:SLIC Subscriber Line Interface Circuit |
| HC5521CQ | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:SLIC Subscriber Line Interface Circuit |
| HC5523 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:LSSGR/TR57 CO/Loop Carrier SLIC with Low Power Standby |
發布緊急采購，3分鐘左右您將得到回復。