- 您現在的位置：買賣IC網 > PDF目錄385344 > GS9021ACFU (Gennum Corporation) GENLINX -TM II GS9021A EDH Coprocessor PDF資料下載
參數資料
| 型號： | GS9021ACFU |
| 廠商： | Gennum Corporation |
| 英文描述： | GENLINX -TM II GS9021A EDH Coprocessor |
| 中文描述： | GENLINX -商標二GS9021A硬腦膜外血腫協處理器 |
| 文件頁數： | 8/26頁 |
| 文件大?。?/td> | 245K |
| 代理商： | GS9021ACFU |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁
19983 - 1
8 of 26
G
The SWITCHFLYW control signal is used in applications
where the data input to the GS9021A is switched between
two synchronous signals. In this case, the two signals may
be slightly misaligned and would normally require the
flywheel to completely re-synchronize. In this scenario, the
re-synchronization time would be undesirable. Asserting the
SWITCHFLYW bit of the HOSTIF write table HIGH allows the
flywheel to re-synchronize to the new incoming signal at the
end of the switching line. For this functionality to operate
properly, the two signals must both be in the active picture
portion of the switching line at the time of the switch.
2.2 Accurate FVH Timing Signals
The F[2:0] signals indicate the current field of the video
data. Three F bits are necessary to accommodate the
composite PAL standard which has 8 fields. For component
standards only F0 is used to represent F = 0 or F = 1. The
F[2:0] bits are available on dedicated output pins and via
the HOSTIF read table. Figure 4a and 4b illustrate the
position of the F[2:0] transition within a line for component
and composite signals, respectively. The lines on which the
transitions occur conform to the SMPTE standards.
For component signals, the horizontal (H) signal is HIGH
during the horizontal blanking region of the output signal,
from EAV to SAV inclusive. For composite signals, the H
signal remains HIGH only for the 3FF, 000, 000, 000, and
TRSID words. Figure 4a and 4b illustrate the H output signal
timing for component and composite signals, respectively.
The vertical (V) signal timing is dependent on the incoming
video standard and the VBLANKS/L control signal. The
VBLANKS/L signal is available as an input pin and via the
HOSTIF write table and should be set to indicate the form of
the incoming data stream. This allows the flywheel to
correctly structure the V bit for flywheel synchronization,
TRS insertion, and TRS error indication.
For component based standards, the transition of the V
output signal within a line is shown in Figure 4a. The line on
which the V output signal transitions from HIGH to LOW is
summarized in the following table.
The lines on which the LOW to HIGH transition occurs
conform to the SMPTE standards.
For composite based standards, the V output signal is
asserted HIGH as described in the table below:
2.3 TRS Errors
The flywheel is also used to indicate TRS errors. These
errors are detected by comparing the TRS in the incoming
data stream with the expected TRS based on the internal
flywheel.
PIN
LOGIC OPR
HOST BIT
F[2:0]
F[2:0]
V
H
VBLANKS/L
AND
VBLANKS/L
STANDARD
VBLANKS/
L
=1
VBLANKS/
L
=0
NTSC 4:2:2 Component
(13.5MHz Y sampling)
9/272
19/282
NTSC 4:2:2 16x9 Widescreen
(18MHz Y sampling)
9/272
19/282
NTSC 4:4:4:4 Single Link
(13.5MHz Y sampling)
9/272
19/282
PAL 4:2:2 Component
(13.5MHz Y sampling)
22/335
22/335
PAL 4:2:2 16x9 Widescreen
(18MHz Y sampling)
22/335
22/335
PAL 4:4:4:4 Single Link
(13.5MHz Y sampling)
22/335
22/335
VBLANKS/
L
=1
VBLANKS/
L
=0
NTSC
Composite
from Line 525/ Sample
768 to Line 9/ Sample
767 inclusive
AND
from Line 263/ Sample
313 to Line 272/
Sample 767 inclusive
from Line 525/ Sample
768 to Line 19/ Sample
767 inclusive
AND
from Line 263/ Sample
313 to Line 282/
Sample 767 inclusive
VBLANKS/
L
=1
VBLANKS/
L
=0
PAL
Composite
from Line 623/ Sample
382 to Line 5/ Sample
947 inclusive
AND
from Line 310/ Sample
948 to Line 317/
Sample 947 inclusive
from Line 623/ Sample
382 to Line 15/ Sample
947 inclusive
AND
from Line 310/ Sample
948 to Line 327/
Sample 947 inclusive
PIN
LOGIC OPR
HOST BIT
TRS_ERROR
相關PDF資料 |
PDF描述 |
|---|---|
| GS9022-CPJ | Digital Video Serializer |
| GS9022 | Digital Video Serializer |
| GS9022-CTJ | Digital Video Serializer |
| GS9022ACPJE3 | GENLINXTM GS9022A Digital Video Serializer |
| GS9022ACTJE3 | GENLINXTM GS9022A Digital Video Serializer |
相關代理商/技術參數 |
參數描述 |
|---|---|
| GS9021ACFUE3 | 制造商:Semtech Corporation 功能描述: 制造商:Semtech Corporation 功能描述:EDH Co-Processer |
| GS9021-CFU | 制造商:Gennum Corporation 功能描述: |
| GS9021-CTU | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:EDH Coprocessor |
| GS9022 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Digital Video Serializer |
| GS9022A | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Serializer for SDI at 270-360Mb/s with Cable Driver |
發布緊急采購，3分鐘左右您將得到回復。