- 您現在的位置：買賣IC網 > PDF目錄375723 > FAN5019B (Fairchild Semiconductor Corporation) 6-Bit VID Controller 2-4 Phase VR10.X Controller PDF資料下載
參數資料
| 型號： | FAN5019B |
| 廠商： | Fairchild Semiconductor Corporation |
| 英文描述： | 6-Bit VID Controller 2-4 Phase VR10.X Controller |
| 中文描述： | 6期西元控制器2-4位的VR10.X控制器 |
| 文件頁數： | 16/30頁 |
| 文件大?。?/td> | 508K |
| 代理商： | FAN5019B |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁
FAN5019B
PRODUCT SPECIFICATION
16
REV. 1.0.0 Jul/15/05
amplifier, and a filter capacitor is placed in parallel with this
resistor. The amplifier’s gain is programmable by adjusting
the feedback resistor to set the load line required by the
microprocessor. The current information is then given as the
difference of CSREF –CSCOMP. This difference signal is
used internally to offset the VID DAC for voltage position-
ing and as a differential input for the current limit compara-
tor.
To provide the best accuracy for the current sensing, the
CSA is designed to have a low offset input voltage. Also,
external resistors determine the sensing gain so that it can be
made extremely accurate and flexible.
Active Impedance Control Mode
For controlling the output voltage droop as a function of
output current, the current sense amplifier (CSA) creates a
voltage signal proportional to the total inductor currents.
External components determine the ratio of this voltage to
the output current to allow it to be adjusted to set the
required load line. Inside the chip the CSA output voltage is
subtracted from the DAC voltage which then is used for the
reference to the error amplifier. As the output current
increases the reference to the error amp decreases causing
the output voltage to decrease accordingly.
Current Control Mode and Thermal Balance
The FAN5019B has individual inputs for each phase which
are used for monitoring the current in each phase. This infor-
mation is combined with an internal ramp to create a current
balancing feedback system that is optimized for initial cur-
rent balance accuracy and dynamic thermal balancing during
operation. This current balance information is independent
of the average output current information used for position-
ing described previously.
The magnitude of the internal ramp can be set to optimize
the transient response of the system. It also monitors the sup-
ply voltage for feed-forward control for changes in the sup-
ply. A resistor connected from the power input voltage to the
RAMPADJ pin determines the slope of the internal PWM
ramp. Detailed information about programming the ramp is
given in the Application Information section.
External resistors can be placed in series with individual
phases to create an intentional current imbalance if desired,
such as when one phase may have better cooling and can
support higher currents. Resistors R
SW1
through R
SW4
(see the typical application circuit in Figure 4) can be used
for adjusting FET thermal and current balance. Zero ohm
placeholder resistors should be provided in the initial layout
to allow the phase balance to be adjusted during design fine
tuning.
To increase the current in any given phase, make R
SW
for
that phase larger (make R
SW
= 0 for the hottest phase and do
not change during balancing). Increasing R
SW
to only 500
Ω
will substantially increase the phase current. Increase each
R
SW
value by small amounts to achieve balance,
starting with the coolest phase first.
Voltage Control Mode
The voltage-mode control loop uses a high gain-bandwidth
voltage mode error amplifier. The control input voltage to
the positive input is set via the VID 6-bit logic code, accord-
ing to the voltages listed in Table 1. This voltage is also off-
set by the droop voltage for active positioning of the output
voltage as a function of current, commonly known as active
voltage positioning. The output of the amplifier is the COMP
pin, which sets the termination voltage for the internal PWM
ramps.
The negative input (F
B
) is tied to the output sense location
with a resistor R
B
and is used for sensing and controlling the
output voltage at this point. A current source from the F
B
pin
flowing through R
B
is used for setting the no-load offset
voltage from the VID voltage. The no-load voltage will be
negative with respect to the VID DAC. The main loop com-
pensation is incorporated in the feedback network between
FB and COMP.
Soft-Start
The power-on ramp up time of the output voltage is set with
a capacitor and resistor in parallel from the DELAY pin to
ground. The RC time constant also determines the current
limit latch off time as explained in the following section. In
UVLO or when EN is a logic low, the DELAY pin is held at
ground. After the UVLO threshold is reached and EN is a
logic high, the DELAY cap is charged up with an internal
20μA current source. The output voltage follows the ramp-
ing voltage on the DELAY pin, limiting the inrush current.
The soft-start time depends on the value of VID DAC and
C
DLY
, with a secondary effect from R
DLY
. Refer to the Appli-
cation Information section for detailed information on set-
ting C
DLY
.
If EN is taken low or VCC drops below UVLO, the DELAY
cap is reset to ground to be ready for another soft start cycle.
Figure 1 shows a typical start-up sequence for the
FAN5019B.
Over Current Limit and Latch-off Protection
The FAN5019B compares a programmable current limit set
point to the voltage from the output of the current sense
amplifier. The level of current limit is set with the resistor
from the ILIMIT pin to ground. During normal operation,
the voltage on ILIMIT is 3V. The current through the exter-
nal resistor is internally scaled to give a current limit thresh-
old of approximately 10.4mV/μA. If the difference in
voltage between CSREF and CSCOMP rises above the cur-
rent limit threshold, the internal current limit amplifier will
control the internal COMP voltage to maintain the average
output current at the limit.
相關PDF資料 |
PDF描述 |
|---|---|
| FAN5019BMTCX | 6-Bit VID Controller 2-4 Phase VR10.X Controller |
| FAN5019MTC | 6-Bit VID Controller 2-4 Phase VRM10.X Controller |
| FAN5019MTCX | 6-Bit VID Controller 2-4 Phase VRM10.X Controller |
| FAN5019 | 6-Bit VID Controller 2-4 Phase VRM10.X Controller |
| FAN5026 | Dual DDR/Dual-output PWM Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| FAN5019BMTCX | 功能描述:DC/DC 開關控制器 ANG FG PWM 4 pases controller RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| FAN5019MTC | 功能描述:DC/DC 開關控制器 PWM 4 phases contrlr RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| FAN5019MTCX | 功能描述:DC/DC 開關控制器 Sync Buck Controller RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| FAN501MPX | 制造商:Fairchild Semiconductor Corporation 功能描述:PWM CONTROLLER - Tape and Reel |
| FAN5020_AAC3116B WAF | 制造商:Fairchild Semiconductor Corporation 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。