- 您現在的位置：買賣IC網 > PDF目錄16543 > EVAL-ADV7180-32EBZ (Analog Devices Inc)BOARD EVAL FOR ADV7180 PDF資料下載
參數資料
| 型號： | EVAL-ADV7180-32EBZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 50/116頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD EVAL FOR ADV7180 |
| 標準包裝： | 1 |
| 系列： | Advantiv® |
| 主要目的： | 視頻，SDTV 視頻解碼器 - NTSC，PAL，SECAM |
| 嵌入式： | 否 |
| 已用 IC / 零件： | ADV7180 |
| 主要屬性： | CVBS（復合），Y/C（S 視頻）和 YPrPb（元件）輸入 |
| 次要屬性： | 8 位 ITU-R BT.656 YCrCb 4:2:2 輸出 |
| 已供物品： | 板 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁當前第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁
Data Sheet
ADV7180
Rev. I | Page 39 of 116
CAGT[1:0], Chroma Automatic Gain Timing,
Address 0x2D[7:6]
The chroma automatic gain timing register allows the user to
influence the tracking speed of the chroma automatic gain
control. This register has an effect only if the CAGC[1:0]
register is set to 10 (automatic gain).
Table 45. CAGT Function
CAGT[1:0]
Description
00
Slow (TC = 2 sec)
01
Medium (TC = 1 sec)
10
Reserved
11 (default)
Adaptive
CG[11:0], Chroma Gain, Address 0x2D[3:0],
Address 0x2E[7:0]; CMG[11:0], Chroma Manual Gain,
Address 0x2D[3:0], Address 0x2E[7:0]
Chroma gain[11:0] is a dual-function register. If written to, a
desired manual chroma gain can be programmed. This gain
becomes active if the CAGC[1:0] function is switched to manual
fixed gain. See Equation 2 for calculating a desired gain.
If read back, this register returns the current gain value.
Depending on the setting in the CAGC[1:0] bits, this is either:
The chroma manual gain value (CAGC[1:0] set to chroma
manual gain mode).
The chroma automatic gain value (CAGC[1:0] set to any of
the automatic modes).
Table 46. CG/CMG Function
CG[11:0]/CMG[11:0]
Read/Write
Description
CMG[11:0]
Write
Manual gain for chroma
path
CG[11:0]
Read
Currently active gain
Chroma_Gain
tor
brationFac
ChromaCali
CMG
decimal
]
0
:
11
[
(2)
where ChromaCalibrationFactor is a decimal value between 0
and 4095.
Calculation of the Chroma Calibration Factor
1. Apply a CVBS signal with the color bars/SMPTE bars test
pattern content directly to the measurement equipment.
2. Ensure correct termination of 75 on the measurement
equipment. Measure chroma output levels.
3. Reconnect the source to the CVBS input of the ADV7180
system that has a backend gain of 1. Repeat the
measurement of chroma levels.
4. Turn off the Chroma AGC and manually change the
Chroma Gain Control Register CMG[11:0] until the
chroma level matches that measured directly from the
source.
This value, in decimal, is the chroma calibration factor.
CKE, Color Kill Enable, Address 0x2B[6]
The color kill enable bit allows the optional color kill function
to be switched on or off.
For QAM-based video standards (PAL and NTSC) as well as
FM-based systems (SECAM), the threshold for the color kill
decision is selectable via the CKILLTHR[2:0] bits.
If color kill is enabled and the color carrier of the incoming
video signal is less than the threshold for 128 consecutive video
lines, color processing is switched off (black and white output).
To switch the color processing back on, another 128 consecutive
lines with a color burst greater than the threshold are required.
The color kill option works only for input signals with a modulated
chroma part. For component input (YPrPb), there is no color kill.
Setting CKE to 0 disables color kill.
Setting CKE to 1 (default) enables color kill.
CKILLTHR[2:0], Color Kill Threshold, Address 0x3D[6:4]
The CKILLTHR[2:0] bits allow the user to select a threshold for
the color kill function. The threshold applies only to QAM-based
(NTSC and PAL) or FM-modulated (SECAM) video standards.
To enable the color kill function, the CKE bit must be set. For
Setting 000, Setting 001, Setting 010, and Setting 011, chroma
demodulation inside the ADV7180 may not work satisfactorily
for poor input video signals.
Table 47. CKILLTHR Function
Description
CKILLTHR[2:0]
SECAM
NTSC, PAL
000
No color kill
Kill at <0.5%
001
Kill at <5%
Kill at <1.5%
010
Kill at <7%
Kill at <2.5%
011 (default)
Kill at <8%
Kill at <4%
100
Kill at <9.5%
Kill at <8.5%
101
Kill at <15%
Kill at <16%
110
Kill at <32%
111
Reserved for Analog Devices internal use only;
do not select
相關PDF資料 |
PDF描述 |
|---|---|
| M1DXK-2436J | IDC CABLE - MKR24K/MC24G/X |
| AD818AR-EBZ | BOARD EVAL FOR AD818AR |
| 5504970-2 | CABLE ASSEM FIBER SC-SC 2 METER |
| AD817AR-EBZ | BOARD EVAL FOR AD817AR |
| AD813AR-14-EBZ | BOARD EVAL FOR AD813AR-14 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EVAL-ADV7180-48EBZ | 制造商:AD 制造商全稱:Analog Devices 功能描述:10-Bit, 4?? Oversampling SDTV Video Decoder |
| EVAL-ADV7180-48EBZ-8P-CAL | 制造商:Analog Devices 功能描述: |
| EVAL-ADV7180LFEB | 制造商:Analog Devices 功能描述:ADV7180 EVAL BOARD - Bulk |
| EVAL-ADV7180LFEBZ | 功能描述:BOARD EVAL FOR ADV7180 LFCSP RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:Advantiv® 標準包裝:1 系列:PSoC® 主要目的:電源管理，熱管理 嵌入式:- 已用 IC / 零件:- 主要屬性:- 次要屬性:- 已供物品:板，CD，電源 |
| EVAL-ADV7180LQEBZ | 功能描述:BOARD EVALUATION ADV7180 RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:Advantiv® 標準包裝:1 系列:- 主要目的:電信，線路接口單元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要屬性:T1/J1/E1 LIU 次要屬性:- 已供物品:板，電源，線纜，CD 其它名稱:82EBV2081 |
發布緊急采購，3分鐘左右您將得到回復。