參數資料
型號： EVAL-AD7686CBZ
廠商： Analog Devices Inc
文件頁數： 7/28頁
文件大?。?/td> 0K
描述： BOARD EVALUATION FOR AD7686
標準包裝： 1
系列： PulSAR®
ADC 的數量： 1
位數： 16
采樣率（每秒）： 500k
數據接口： 串行
輸入范圍： ±VREF
在以下條件下的電源（標準）： 15mW @ 500kSPS，5 V
工作溫度： -40°C ~ 85°C
已用 IC / 零件： AD7686
已供物品： 板
相關產品： AD7686CCPZRL7TR-ND - IC ADC 16BIT SAR 500KSPS 10LFCSP
AD7686CCPZRL-ND - IC ADC 16BIT SAR 500KSPS 10LFCSP
AD7686BCPZRL7TR-ND - IC ADC 16BIT 500KSPS 10-LFCSP
AD7686BCPZRL-ND - IC ADC 16BIT 500KSPS 10-LFCSP
AD7686CRMZ-ND - IC ADC 16BIT 500KSPS 10MSOP
AD7686BRMZ-ND - IC ADC 16BIT 500KSPS 10-MSOP
AD7686CRMZRL7-ND - IC ADC 16BIT 500KSPS 10MSOP
AD7686BRMZRL7-ND - IC ADC 16BIT 500KSPS 10MSOP
AD7686
Rev. B | Page 15 of 28
DRIVER AMPLIFIER CHOICE
Although the AD7686 is easy to drive, the driver amplifier
should meet the following requirements:
The noise generated by the driver amplifier needs to be
kept as low as possible to preserve the SNR and transition
noise performance of the AD7686. Note that the AD7686
has a noise much lower than most of the other 16-bit
ADCs and, therefore, can be driven by a noisier amplifier
to meet a given system noise specification. The noise
coming from the amplifier is filtered by the AD7686 analog
input circuit 1-pole, low-pass filter made by RIN and CIN or
by the external filter, if one is used. Because the typical
noise of the AD7686 is 37 μV rms, the SNR degradation
due to the amplifier is
+
=
2
)
(
2
π
37
20log
N
3dB
LOSS
Ne
f
SNR
where:
f–3dB is the input bandwidth in MHz of the AD7686
(9 MHz) or the cutoff frequency of the input filter, if
one is used.
N is the noise gain of the amplifier (for example, 1 in buffer
configuration).
eN is the equivalent input noise voltage of the op amp,
in nV/√Hz.
For ac applications, the driver should have a THD
performance commensurate with the AD7686. Figure 18
shows the THD vs. frequency that the driver should exceed.
For multichannel multiplexed applications, the driver
amplifier and the AD7686 analog input circuit must settle a
full-scale step onto the capacitor array at a 16-bit level
(0.0015%). In the data sheet for the amplifier, settling at
0.1% to 0.01% is more commonly specified. This could
differ significantly from the settling time at a 16-bit level
and should be verified prior to driver selection.
Table 8. Recommended Driver Amplifiers
Amplifier
Typical Application
Very low noise and low power
5 V single-supply, low power
5 V single-supply, low power
Low power, low noise, and low frequency
Very low noise and high frequency
Very low noise and high frequency
Small, low power and low frequency
High frequency and low power
VOLTAGE REFERENCE INPUT
The AD7686 voltage reference input, REF, has a dynamic input
impedance and should, therefore, be driven by a low impedance
source with efficient decoupling between the REF and GND
pins, as explained in the Layout section.
When REF is driven by a very low impedance source, such as a
reference buffer using the AD8031 or the AD8605, a 10 μF
(X5R, 0805 size) ceramic chip capacitor is appropriate for
optimum performance.
If an unbuffered reference voltage is used, the decoupling value
depends on the reference used. For instance, a 22 μF (X5R,
1206 size) ceramic chip capacitor is appropriate for optimum
performance using a low temperature drift ADR43x reference.
If desired, smaller reference decoupling capacitor values down
to 2.2 μF can be used with a minimal impact on performance,
especially DNL.
Regardless, there is no need for an additional lower value
ceramic decoupling capacitor, such as 100 nF, between the REF
and GND pins.
POWER SUPPLY
The AD7686 is specified at 4.5 V to 5.5 V. The device uses two
power supply pins: a core supply VDD and a digital input/
output interface supply VIO. VIO allows direct interface with
any logic between 1.8 V and VDD. To reduce the supplies
needed, the VIO and VDD can be tied together.
The AD7686 is independent of power supply sequencing
between VIO and VDD. Additionally, it is very insensitive to
power supply variations over a wide frequency range, as shown
in Figure 30, which represents PSRR over frequency.
0
29
69-
031
FREQUENCY (kHz)
10000
1
1000
10
100
P
S
RR
(
d
B)
110
100
90
80
70
60
50
40
30
VDD = 5V
Figure 30. PSRR vs. Frequency
相關PDF資料
PDF描述
HBC06DRTH-S93 CONN EDGECARD 12POS DIP .100 SLD
MCP355XDV-MS1 BOARD DEV SENSOR APP MCP355X
UPB2D681MRD CAP ALUM 680UF 200V 20% RADIAL
MLG1005S68NJ INDUCTOR MULTILAYER 68NH 0402
GCC06DRYI-S93 CONN EDGECARD 12POS DIP .100 SLD
相關代理商/技術參數
參數描述
EVAL-AD7686SDZ 功能描述:數據轉換 IC 開發工具 EVAL BOARD 100Ksps/400Ksps 16 bit I.C RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V
EVAL-AD7687CB 制造商:Analog Devices 功能描述:EVAL BOARD 16-BIT, 250KSPS DIFFER . I.C. - Bulk
EVAL-AD7687CBZ 功能描述:BOARD EVALUATION FOR AD7687 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:PulSAR® 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件
EVAL-AD7687SDZ 功能描述:BOARD EVAL FOR AD7687 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:PulSAR® 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件
EVAL-AD7688CB 制造商:Analog Devices 功能描述:EVAL BD FOR USE W/ EITHER THE ANLG DEVICES - Bulk
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購
*
*
*