- 您現在的位置：買賣IC網 > PDF目錄384299 > EUA5202QIT (Electronic Theatre Controls, Inc.) 2-W Stereo Audio Power Amplifier with Mute PDF資料下載
參數資料
| 型號： | EUA5202QIT |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | 2-W Stereo Audio Power Amplifier with Mute |
| 中文描述： | 2 - W型立體聲音頻功率放大器靜音 |
| 文件頁數： | 20/22頁 |
| 文件大小： | 680K |
| 代理商： | EUA5202QIT |
EUA5202
DS5202 Ver 1.4 Nov. 2004
In a typical computer sound channel operating at 5V,
bridging raises the power into
an
8-
speaker from a
singled -ended (SE, ground reference) limit of 250 mW
to 1W. In sound power that is a 6-dB improvement—
which is loudness that can be heard. In addition to
increased power there are frequency response concerns.
Consider the single-supply SE configuration shown in
Figure 57. A coupling capacitor is required to block the
dc offset voltage from reaching the load. These
capacitors can be quite large (approximately 33
μ
F to
1000
μ
F) so they tend to be expensive, heavy, occupy
valuable PCB area, and have the additional drawback of
limiting low-frequency performance of the system.
This frequency limiting effect is due to the high pass
filter network created with the speaker impedance and
the coupling capacitance
and is calculated with equation
8.
f
C
=
L
C
R
2
For example,
a 68
μ
F capacitor with
an 8-
speaker
would attenuate low frequencies below 293 Hz. The
BTL configuration cancels the dc offsets, which
eliminates the need for the blocking capacitors.
Low-frequency performance is then limited only by the
input network and speaker response. Cost and PCB
space are also minimized by eliminating the bulky
coupling capacitor.
C
1
π
------------------------------------
(8)
Increasing power to the load does carry a penalty of
increased internal power dissipation. The increased
dissipation is understandable considering that the BTL
configuration produces 4 the output power of the SE
configuration. Internal dissipation versus output power is
discussed further in the crest factor and thermal
considerations section
.
S
ingle-Ended Operation
In SE mode (see Figure56 and Figure57), the load is
driven from the primary amplifier output for each
channel (OUT+, terminals 22 and 3).
In SE mode the gain is set by the R
F
and R
I
resistors and
is shown in equation 9. Since the inverting amplifier is
not used to mirror the voltage swing on the load, the
factor of 2, from equation 5, is not included.
SE Gain =
I
R
F
R
-------------------------------------- (9)
The output coupling capacitor required in single-supply
SE mode also places additional constraints on the
selection of other components in the amplifier circuit.
The rules described earlier still hold with the addition of
the following relationship (see equation 10):
C
C
L
R
1
I
R
I
C
1
k
25
B
C
1
<
≤
×
--------------- (10)
相關PDF資料 |
PDF描述 |
|---|---|
| EV0005 | High Efficiency White LED Driver |
| EV0021 | High Efficiency White LED Driver |
| EV0100 | SINGLE TONE SIREN/ALARM SOUND GENERATOR |
| EV2200 | PC Interface Board for Gas Gauge Evaluation(電池容量PC接口評估板) |
| EVA2023RS28 | 2.4 GHz 802.11b/g WLAN Power Amplifier |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EUA5202QIT0 | 制造商:EUTECH 制造商全稱:Eutech Microelectronics Inc 功能描述:2-W Stereo Audio Power Amplifier with Mute |
| EUA5202QIT1 | 制造商:EUTECH 制造商全稱:Eutech Microelectronics Inc 功能描述:2-W Stereo Audio Power Amplifier with Mute |
| EUA5212 | 制造商:EUTECH 制造商全稱:Eutech Microelectronics Inc 功能描述:2-W Stereo Audio Power Amplifier with Four Selectable Gain Settings |
| EUA5212QIR | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:2-W Stereo Audio Power Amplifier with Four Selectable Gain Settings |
| EUA5212QIR0 | 制造商:EUTECH 制造商全稱:Eutech Microelectronics Inc 功能描述:2-W Stereo Audio Power Amplifier with Four Selectable Gain Settings |
發布緊急采購，3分鐘左右您將得到回復。