- 您現在的位置：買賣IC網 > PDF目錄10585 > EL4511CUZ-T7A (Intersil)IC VID SYNC SEPARATR HDTV 24QSOP PDF資料下載
參數資料
| 型號： | EL4511CUZ-T7A |
| 廠商： | Intersil |
| 文件頁數： | 13/24頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC VID SYNC SEPARATR HDTV 24QSOP |
| 標準包裝： | 250 |
| 類型： | 同步分離器 |
| 應用： | HDTV，投影儀，機頂盒 |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 24-SSOP（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 24-QSOP |
| 包裝： | 帶卷 (TR) |
20
FN7009.8
November 12, 2010
Serial Mode Operation
See “Description of Operation” for more details of (Serial
Mode).
Using the Reference Oscillator and Counter
A counter is provided for measuring the vertical time interval;
this counts the clocks at the XTAL pin 1 between vertical
pulses.
This information is not necessary for the operation of the
chip; only for information to the system micro-control. The
count value is read from register 14 at bits 7:6 for the MSBs,
the LSBs are available in register 13, bits 7:0. Register 14,
bit 4 should be a high to indicate that the read operation did
not collide with the up-date timing.
If the crystal oscillator is enabled through the serial interface
(Register 9, bit 6, ENXTAL), the XTAL and XTALN pins will
become the crystal input and crystal output pins for the
32.7kHz crystal. It is also possible to drive the XTAL pin with
a logic level clock up to a maximum of 50kHz; this signal is
only used to measure the vertical rate.
Example:
Using a 32.768kHz crystal, the count period is 30.52s. With
a 20ms vertical rate, there will be approximately 656 cycles
(290 Hex) in the "counts per field" registers 13 and 14. With
a 16.666'ms vertical rate, the count of 546 (222 Hex) will be
seen.
Computer & Control Interface
In addition to the mode control pins, the chips default
operating mode may be changed by way of a serial
interface. This is of the three-wire type, Data, clock and
/enable. After the /ENABLE line (pin 5) is taken low, the 16
bits of data on the SDA pin 7 will be clocked into the chip by
the clock signal SCL pin 6. See Figure 10.
The first bit of the data determines whether it will be a read
or write operation. When set to a "0", a write operation will
take place. The following 7 bits, select the register to be
written to. Finally, the last 8 bits are the data to be written or
read. For a read operation, the first bit is a "1".
In general, when registers entries are changed, the
unchanged register bits must have the “Reset Values”
entered as defined by Table 5.
MODE
DECODE
(SEE TABLE 3)
10 BIT COUNTER
CLK
R
Q0
Q7
Q8
Q9
Q0
Q7
Q6
Q7
REGISTER 13
REGISTER 14
LD
TIMING
VERTOUT
REGISTER 9
BIT 6
XTAL
(PIN 1)
XTALN
(PIN 24)
TO SERIAL I/F
REGISTER 1, BITS 5:3
REGISTER 2, BIT 0
3
8
‘1’
‘0’
FIGURE 10. BLOCK DIAGRAM OF REFERENCE OSCILLATOR
EL4511
相關PDF資料 |
PDF描述 |
|---|---|
| VE-JTK-MY-F4 | CONVERTER MOD DC/DC 40V 50W |
| VE-27M-IW-F2 | CONVERTER MOD DC/DC 10V 100W |
| SF6282-4PG-520 | CONN PLUG 4POS CABLE PIN |
| T 3650 001 | CONN CIR MALE 14POS CBL MNT |
| ISL59603IRZ-T7 | IC VIDEO EQUALIZER 20-QFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EL4511CUZ-T7S2705 | 制造商:Intersil Corporation 功能描述:CISCO, EL4511CUZ-T7 W/CONTAINER LABELING - Tape and Reel |
| EL452(TA)-VG | 制造商:EVERLIGHT 制造商全稱:Everlight Electronics Co., Ltd 功能描述:4 PIN SOP HIGH VOLTAGE DARLINGTON |
| EL452(TB)-VG | 制造商:EVERLIGHT 制造商全稱:Everlight Electronics Co., Ltd 功能描述:4 PIN SOP HIGH VOLTAGE DARLINGTON |
| EL452-G | 制造商:EVERLIGHT 制造商全稱:Everlight Electronics Co., Ltd 功能描述:4 PIN SOP HIGH VOLTAGE DARLINGTON |
| EL4543 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Triple Differential Twisted-Pair Driver with Common-Mode Sync Encoding |
發布緊急采購，3分鐘左右您將得到回復。