Use the value obtained by the equation (T" />
參數資料
型號: DSP56F805FV80E
廠商: Freescale Semiconductor
文件頁數: 47/56頁
文件大?。?/td> 0K
描述: IC DSP 80MHZ 64KB FLASH 144LQFP
標準包裝: 60
系列: 56F8xx
核心處理器: 56800
芯體尺寸: 16-位
速度: 80MHz
連通性: CAN,EBI/EMI,SCI,SPI
外圍設備: POR,PWM,WDT
輸入/輸出數: 32
程序存儲器容量: 71KB(35.5K x 16)
程序存儲器類型: 閃存
RAM 容量: 2.5K x 16
電壓 - 電源 (Vcc/Vdd): 3 V ~ 3.6 V
數據轉換器: A/D 8x12b
振蕩器型: 外部
工作溫度: -40°C ~ 85°C
封裝/外殼: 144-LQFP
包裝: 托盤
Electrical Design Considerations
56F805 Technical Data, Rev. 16
Freescale Semiconductor
51
Use the value obtained by the equation (TJ – TT)/PD where TT is the temperature of the package case
determined by a thermocouple.
The thermal characterization parameter is measured per JESD51-2 specification using a 40-gauge type T
thermocouple epoxied to the top center of the package case. The thermocouple should be positioned so
that the thermocouple junction rests on the package. A small amount of epoxy is placed over the
thermocouple junction and over about 1mm of wire extending from the junction. The thermocouple wire
is placed flat against the package case to avoid measurement errors caused by cooling effects of the
thermocouple wire.
When heat sink is used, the junction temperature is determined from a thermocouple inserted at the
interface between the case of the package and the interface material. A clearance slot or hole is normally
required in the heat sink. Minimizing the size of the clearance is important to minimize the change in
thermal performance caused by removing part of the thermal interface to the heat sink. Because of the
experimental difficulties with this technique, many engineers measure the heat sink temperature and then
back-calculate the case temperature using a separate measurement of the thermal resistance of the
interface. From this case temperature, the junction temperature is determined from the junction-to-case
thermal resistance.
5.2 Electrical Design Considerations
Use the following list of considerations to assure correct operation:
Provide a low-impedance path from the board power supply to each VDD pin on the controller, and from the
board ground to each VSS pin.
The minimum bypass requirement is to place 0.1
μF capacitors positioned as close as possible to the package
supply pins. The recommended bypass configuration is to place one bypass capacitor on each of the
VDD/VSS pairs, including VDDA/VSSA. Ceramic and tantalum capacitors tend to provide better performance
tolerances.
Ensure that capacitor leads and associated printed circuit traces that connect to the chip VDD and VSS pins
are less than 0.5 inch per capacitor lead.
Bypass the VDD and VSS layers of the PCB with approximately 100μF, preferably with a high-grade
capacitor such as a tantalum capacitor.
CAUTION
This device contains protective circuitry to guard against
damage due to high static voltage or electrical fields.
However, normal precautions are advised to avoid
application of any voltages higher than maximum rated
voltages to this high-impedance circuit. Reliability of
operation is enhanced if unused inputs are tied to an
appropriate voltage level.
相關PDF資料
PDF描述
DSP56F807VF80E IC DSP 80MHZ 60K FLASH 160-BGA
DSP56F826BU80 IC DSP 80MHZ 64KB FLASH 100LQFP
DSP56F827FG80E IC HYBRID CTRLR 16BIT 128-LQFP
DSPB56362AG120 IC DSP 24BIT AUD 120MHZ 144-LQFP
DSPB56364AF100 IC DSP 24BIT AUD 100MHZ 100-LQFP
相關代理商/技術參數
參數描述
DSP56F805FV80E 制造商:Freescale Semiconductor 功能描述:Digital Signal Processor IC DSP Type:Cor
DSP56F805FV80E 制造商:Freescale Semiconductor 功能描述:DSP LQFP144 3.6V
DSP56F805PB 制造商:未知廠家 制造商全稱:未知廠家 功能描述:56F805 16-Bit Hybrid Controller Product Brief
DSP56F807 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:56F807 16-bit Hybrid Processor
DSP56F807EVM 功能描述:開發板和工具包 - 其他處理器 Evaluation Kit For DSP56F807 RoHS:否 制造商:Freescale Semiconductor 產品:Development Systems 工具用于評估:P3041 核心:e500mc 接口類型:I2C, SPI, USB 工作電源電壓: