Use the value obtained by the equation (T" />
參數資料
型號： DSP56F805FV80
廠商： Freescale Semiconductor
文件頁數： 47/56頁
文件大?。?/td> 0K
描述： IC DSP 80MHZ 64KB FLASH 144LQFP
標準包裝： 60
系列： 56F8xx
核心處理器： 56800
芯體尺寸： 16-位
速度： 80MHz
連通性： CAN，EBI/EMI，SCI，SPI
外圍設備： POR，PWM，WDT
輸入/輸出數： 32
程序存儲器容量： 71KB（35.5K x 16）
程序存儲器類型： 閃存
RAM 容量： 2.5K x 16
電壓 - 電源 (Vcc/Vdd)： 3 V ~ 3.6 V
數據轉換器： A/D 8x12b
振蕩器型： 外部
工作溫度： -40°C ~ 85°C
封裝/外殼： 144-LQFP
包裝： 托盤
Electrical Design Considerations
56F805 Technical Data, Rev. 16
Freescale Semiconductor
51
Use the value obtained by the equation (TJ – TT)/PD where TT is the temperature of the package case
determined by a thermocouple.
The thermal characterization parameter is measured per JESD51-2 specification using a 40-gauge type T
thermocouple epoxied to the top center of the package case. The thermocouple should be positioned so
that the thermocouple junction rests on the package. A small amount of epoxy is placed over the
thermocouple junction and over about 1mm of wire extending from the junction. The thermocouple wire
is placed flat against the package case to avoid measurement errors caused by cooling effects of the
thermocouple wire.
When heat sink is used, the junction temperature is determined from a thermocouple inserted at the
interface between the case of the package and the interface material. A clearance slot or hole is normally
required in the heat sink. Minimizing the size of the clearance is important to minimize the change in
thermal performance caused by removing part of the thermal interface to the heat sink. Because of the
experimental difficulties with this technique, many engineers measure the heat sink temperature and then
back-calculate the case temperature using a separate measurement of the thermal resistance of the
interface. From this case temperature, the junction temperature is determined from the junction-to-case
thermal resistance.
5.2 Electrical Design Considerations
Use the following list of considerations to assure correct operation:
Provide a low-impedance path from the board power supply to each VDD pin on the controller, and from the
board ground to each VSS pin.
The minimum bypass requirement is to place 0.1
μF capacitors positioned as close as possible to the package
supply pins. The recommended bypass configuration is to place one bypass capacitor on each of the
VDD/VSS pairs, including VDDA/VSSA. Ceramic and tantalum capacitors tend to provide better performance
tolerances.
Ensure that capacitor leads and associated printed circuit traces that connect to the chip VDD and VSS pins
are less than 0.5 inch per capacitor lead.
Bypass the VDD and VSS layers of the PCB with approximately 100μF, preferably with a high-grade
capacitor such as a tantalum capacitor.
CAUTION
This device contains protective circuitry to guard against
damage due to high static voltage or electrical fields.
However, normal precautions are advised to avoid
application of any voltages higher than maximum rated
voltages to this high-impedance circuit. Reliability of
operation is enhanced if unused inputs are tied to an
appropriate voltage level.
相關PDF資料
PDF描述
DSP56F803BU80 IC DSP 80MHZ 64KB FLASH 100LQFP
MC68332ACFC25 IC MCU 32BIT 25MHZ 132-PQFP
MC68332ACFC20 IC MCU 32BIT 20MHZ 132-PQFP
MCF5307FT66B IC MPU 32BIT COLDF 66MHZ 208FQFP
MCF5206FT25A IC MCU 32BIT COLDF 25MHZ 160-QFP
相關代理商/技術參數
參數描述
DSP56F805FV80E 功能描述:數字信號處理器和控制器 - DSP, DSC 80Mhz/40MIPS RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
DSP56F805FV80E 制造商:Freescale Semiconductor 功能描述:Digital Signal Processor IC DSP Type:Cor
DSP56F805FV80E 制造商:Freescale Semiconductor 功能描述:DSP LQFP144 3.6V
DSP56F805PB 制造商:未知廠家 制造商全稱:未知廠家 功能描述:56F805 16-Bit Hybrid Controller Product Brief
DSP56F807 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:56F807 16-bit Hybrid Processor
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*