- 您現在的位置：買賣IC網 > PDF目錄11739 > DS2406P+T&R (Maxim Integrated Products)IC SW DL ADDRESS W/1K MEM 6-TSOC PDF資料下載
參數資料
| 型號： | DS2406P+T&R |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 7/32頁 |
| 文件大小： | 0K |
| 描述： | IC SW DL ADDRESS W/1K MEM 6-TSOC |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 4,000 |
| 應用： | 遙控，遙測 |
| 接口： | 1 線 |
| 電源電壓： | 2.8 V ~ 6 V |
| 封裝/外殼： | 6-LSOJ |
| 供應商設備封裝： | 6-TSOC |
| 包裝： | 帶卷 (TR) |
| 安裝類型： | 表面貼裝 |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
DS2406
15 of 32
The TOG bit of Channel Control Byte 1 specifies if one is always reading or writing (TOG = 0) or if one
is going to change from reading to writing or vice versa after every data byte that has been sent to or
received from the DS2406 (TOG = 1). When accessing one channel, one byte is equivalent to eight reads
from or writes to the selected PIO pin. When accessing two channels, one byte is equivalent to four reads
or writes from/to each channel.
The initial mode (reading or writing) for accessing the PIO channels is specified in the IM bit. For read-
ing, IM has to be set to 1, for writing IM needs to be 0. If the TOG bit is set to 0, the device will always
read or write as specified by the IM bit. If TOG is 1, the device will use the setting of IM for the first byte
to be transmitted and will alternate between reading and writing after every byte. Table 1 illustrates the
effect of TOG and IM for one-channel as well as for two-channel operation.
THE EFFECT OF TOGGLE MODE AND INITIAL MODE Table 1
TOG
IM
CHANNELS
EFFECT
0
one channel
Write all bits to the selected channel
0
1
one channel
Read all bits from the selected channel
1
0
one channel
Write 8 bits, read 8 bits, write, read, etc. to/from
the selected channel
1
one channel
Read 8 bits, write 8 bits, read, write, etc. from/to
the selected channel
0
two channels
Repeat: four times (write A, write B)
0
1
two channels
Repeat: four times (read A, read B)
1
0
two channels
Four times: (write A, write B), four times: (read
A, read B), write, read, etc.
1
two channels
Four times: (read A, read B), four times: (write A,
write B), read, write, etc.
The ALR bit of Channel Control Byte 1 controls whether the activity latch of each channel gets reset.
Both activity latches are cleared simultaneously if the ALR bit is 1. They are not changed if the ALR bit
is 0. An activity latch is set with a negative or positive edge that occurs at its associated PIO channel.
Channel Control Byte 1 also controls the internal CRC generator to safeguard data transmission between
the bus master and the DS2406 for channel access. It does not affect reading from or writing to the
memory sections of the DS2406. The CRC control bits (bit 0 and bit 1) can be set to create and protect
data packets that have the size of 8 bytes or 32 bytes. If desired, the device can safeguard even single
bytes by a 16-bit CRC. This setting, however, limits the average PIO sampling rate to about one third of
its maximum possible value. The codes for the CRC control are shown in the table below.
CRC1
CRC0
Description
0
CRC disabled (no CRC at all)
0
1
CRC after every byte
1
0
CRC after 8 bytes
1
CRC after 32 bytes
The CRC provides a high level of safeguarding data. A detailed description of CRCs is found in
Application Note 27. If the CRC is disabled, the CRC-related sections in the flow chart are skipped.
相關PDF資料 |
PDF描述 |
|---|---|
| 142-0761-821 | CONN JACK SMA 50 OHMS PC MOUNT |
| MS27484E18F35P | CONN PLUG 66POS STRAIGHT W/PINS |
| PIC16C67-20I/P | IC MCU OTP 8KX14 PWM 40DIP |
| VI-B4D-IX-F4 | CONVERTER MOD DC/DC 85V 75W |
| 142-0761-831 | CONN JACK SMA 50 OHMS PC MOUNT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS2406T | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:Dual Addressable Switch Plus 1K-Bit Memory |
| DS2406V | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:Dual Addressable Switch Plus 1K-Bit Memory |
| DS2406X | 功能描述:接口 - 專用 RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| DS2407 | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:Dual Addressable Switch Plus 1K.Bit Memory |
| DS2407FP000 | 制造商:Thomas & Betts 功能描述:200A,CON,3P4W,MG,407,3P250V |
發布緊急采購，3分鐘左右您將得到回復。