參數資料
型號： DS2151QNB
廠商： Maxim Integrated Products
文件頁數： 37/60頁
文件大小： 0K
描述： IC TXRX T1 1-CH 5V LP IND 44PLCC
產品培訓模塊： Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝： 26
功能： 單芯片收發器
接口： T1
電路數： 1
電源電壓： 4.75 V ~ 5.25 V
電流 - 電源： 65mA
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 44-LCC（J 形引線）
供應商設備封裝： 44-PLCC（16.59x16.59）
包裝： 管件
包括： 警報檢測器和發生器，CSU 回路代碼發生器和檢測器，DSX-1和CSU 線路補償發生器
產品目錄頁面： 1429 (CN2011-ZH PDF)
DS2151Q
42 of 60
13.3 Jitter Attenuator
The DS2151Q contains an on-board jitter attenuator that can be set to a depth of either 32 or 128 bits via
the JABDS bit in the Line Interface Control Register (LICR). The 128-bit mode is used in applications
where large excursions of wander are expected. The 32-bit mode is used in delay sensitive applications.
The characteristics of the attenuation are shown in Figure 13-4. The jitter attenuator can be placed in
either the receive path or the transmit path by appropriately setting or clearing the JAS bit in the LICR.
Also, the jitter attenuator can be disabled (in effect, removed) by setting the DJA-bit in the LICR. In order
for the jitter attenuator to operate properly, a crystal with the specifications listed in Table 13-4 below
must be connected to the XTAL1 and XTAL2 pins. The jitter attenuator divides the clock provided by the
6.176MHz crystal at the XTAL1 and XTAL2 pins to create an output clock that contains very little jitter.
On-board circuitry will pull the crystal (by switching in or out load capacitance) to keep it long-term
averaged to the same frequency as the incoming T1 signal. If the incoming jitter exceeds either 120UIP-P
(buffer depth is 128 bits) or 28UIP-P (buffer depth is 32 bits), then the DS2151Q will divide the attached
crystal by either 3.5 or 4.5 instead of the normal 4 to keep the buffer from overflowing. When the device
divides by either 3.5 or 4.5, it also sets the Jitter Attenuator Limit Trip (JALT) bit in the Receive
Information Register 2 (RIR2.2).
Table 13-4. Crystal Selection Guidelines
PARAMETER
SPECIFICATION
Parallel Resonant Frequency
6.176MHz
Mode
Fundamental
Load Capacitance
18pF to 20pF (18.5pF nominal)
Tolerance
±50ppm
Pullability
CL = 10pF, delta frequency = +175ppm to
+250ppm
CL = 45pF, delta frequency = -175ppm to -250ppm
Effective Series Resistance
40
maximum
Crystal Cut
AT
相關PDF資料
PDF描述
VI-B0Z-IY-F1 CONVERTER MOD DC/DC 2V 20W
VI-B0Z-IX-F2 CONVERTER MOD DC/DC 2V 30W
VI-B0Y-IY-F2 CONVERTER MOD DC/DC 3.3V 33W
VI-B0Y-IX-F2 CONVERTER MOD DC/DC 3.3V 49.5W
VI-B0X-IY-F4 CONVERTER MOD DC/DC 5.2V 50W
相關代理商/技術參數
參數描述
DS2151QNB/T&R 制造商:Maxim Integrated Products 功能描述:T1 SINGLE CHIP XCVR REV B IND - Tape and Reel
DS2151QNB/T&R 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS2151QNB+ 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS2151QNB+T&R 制造商:Maxim Integrated Products 功能描述:FRAMER DS1/E1/ISDN-PRI/T1 5V 44PLCC - Tape and Reel
DS2151QNB+T&R 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*