- 您現在的位置：買賣IC網 > PDF目錄97865 > DS1822-PAR (DALLAS SEMICONDUCTOR) DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 0.20Cel, ROUND, THROUGH HOLE MOUNT PDF資料下載
參數資料
| 型號： | DS1822-PAR |
| 廠商： | DALLAS SEMICONDUCTOR |
| 元件分類： | Switch/Digital Output Temperature Sensor |
| 英文描述： | DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 0.20Cel, ROUND, THROUGH HOLE MOUNT |
| 封裝： | TO-92, 3 PIN |
| 文件頁數： | 6/19頁 |
| 文件大?。?/td> | 138K |
| 代理商： | DS1822-PAR |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁
DS1822-PAR
14 of 19
The DS1822-PAR samples the 1-wire bus during a window that lasts from 15
s to 60 s after the master
initiates the write time slot. If the bus is high during the sampling window, a 1 is written to the DS1822-
PAR. If the line is low, a 0 is written to the DS1822-PAR.
READ/WRITE TIME SLOT TIMING DIAGRAM Figure 12
READ TIME SLOTS
The DS1822-PAR can only transmit data to the master when the master issues read time slots. Therefore,
the master must generate read time slots immediately after issuing a Read Scratchpad [BEh] command, so
that the DS1822-PAR can provide the requested data. In addition, the master can generate read time slots
after issuing a Recall E
2 [B8h] command to find out the recall status as explained in the DS1822-PAR
FUNCTION COMMAND section.
All read time slots must be a minimum of 60
s in duration with a minimum of a 1 s recovery time
between slots.
A read time slot is initiated by the master device pulling the 1-wire bus low for a
minimum of 1
s and then releasing the bus (see Figure 12). After the master initiates the read time slot,
the DS1822-PAR will begin transmitting a 1 or 0 on bus. The DS1822-PAR transmits a 1 by leaving the
bus high and transmits a 0 by pulling the bus low. When transmitting a 0, the DS1822-PAR will release
the bus by the end of the time slot, and the bus will be pulled back to its high idle state by the pullup
LINE TYPE LEGEND
Bus master pulling low
DS1822-PAR pulling low
Resistor pullup
45
s
15
s
VPU
GND
1-WIRE BUS
60
s < T
X “0” < 120
1
s < T
REC <
∞
DS1822-PAR samples
MIN
TYP
MAX
15
s
30
s
> 1
s
MASTER WRITE “0” SLOT
MASTER WRITE “1” SLOT
DS1822-PAR samples
MIN
TYP
MAX
VPU
GND
1-WIRE BUS
15
s
MASTER READ “0” SLOT
MASTER READ “1” SLOT
Master samples
START
OF SLOT
START
OF SLOT
> 1
s
1
s < T
REC <
∞
15
s
15
s
30
s
15
s
> 1
s
相關PDF資料 |
PDF描述 |
|---|---|
| DS1822Z/T&R | DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 2Cel, RECTANGULAR, SURFACE MOUNT |
| DS1822/T&R | DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 2Cel, RECTANGULAR, THROUGH HOLE MOUNT |
| DS1822 | DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 2Cel, RECTANGULAR, THROUGH HOLE MOUNT |
| DS1822+T&R | DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 2Cel, RECTANGULAR, THROUGH HOLE MOUNT |
| DS1822Z | DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 2Cel, RECTANGULAR, SURFACE MOUNT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS1822-PAR/T&R | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| DS1822-PAR_07 | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:Econo 1-Wire Parasite-Power Digital Thermometer |
| DS1822-PAR+T&R | 制造商:Maxim Integrated Products 功能描述: 制造商:Maxim Integrated Products 功能描述:TEMP SENSOR DGTL 1-WIRE 3PIN TO-92 - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC THERMOMETER ECONO DIG TO-92 制造商:Maxim Integrated Products 功能描述:Board Mount Temperature Sensors 1-Wire Digital Thermometer |
| DS1822-PAR+T&R | 功能描述:板上安裝溫度傳感器 1-Wire Digital Thermometer RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| DS-18-22-RS | 制造商:TE Connectivity 功能描述:Red sealed splice terminal,0.5-1.5sq.mm |
發布緊急采購，3分鐘左右您將得到回復。