- 您現在的位置：買賣IC網 > PDF目錄97865 > DS1822-PAR (DALLAS SEMICONDUCTOR) DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 0.20Cel, ROUND, THROUGH HOLE MOUNT PDF資料下載
參數資料
| 型號： | DS1822-PAR |
| 廠商： | DALLAS SEMICONDUCTOR |
| 元件分類： | Switch/Digital Output Temperature Sensor |
| 英文描述： | DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 0.20Cel, ROUND, THROUGH HOLE MOUNT |
| 封裝： | TO-92, 3 PIN |
| 文件頁數： | 2/19頁 |
| 文件大小： | 138K |
| 代理商： | DS1822-PAR |
DS1822-PAR
10 of 19
register (byte 3), and the third byte is written into the configuration register (byte 4). Data must be
transmitted least significant bit first. All three bytes MUST be written before the master issues a reset, or
the data may be corrupted.
READ SCRATCHPAD [BEh]
This command allows the master to read the contents of the scratchpad. The data transfer starts with the
least significant bit of byte 0 and continues through the scratchpad until the 9
th byte (byte 8 – CRC) is
read. If only part of the scratchpad contents is required, the master may issue a reset to terminate reading
at any time.
COPY SCRATCHPAD [48h]
This command copies the contents of the scratchpad TH, TL and configuration registers (bytes 2, 3 and 4)
to EEPROM. If the device is being used in parasite power mode, within 10
s (max) after this command
is issued the master must enable a strong pullup on the 1-wire bus for at least 10 ms as described in the
PARASITE POWER section.
RECALL E
2 [B8h]
This command recalls the alarm trigger values (TH and TL) and configuration data from EEPROM and
places the data in bytes 2, 3, and 4, respectively, in the scratchpad memory. The master device can issue
“read time slots” (see the 1-WIRE BUS SYSTEM section) following the Recall E
2 command and the
DS1822-PAR will indicate the status of the recall by transmitting 0 while the recall is in progress and
1 when the recall is done. The recall operation happens automatically at power-up, so valid data is
available in the scratchpad as soon as power is applied to the device.
DS1822-PAR FUNCTION COMMAND SET Table 4
Command
Description
Protocol
1-Wire Bus Activity
After Command is Issued
Notes
TEMPERATURE CONVERSION COMMANDS
Convert T
Initiates temperature
conversion.
44h
None
1
MEMORY COMMANDS
Read Scratchpad
Reads the entire scratchpad
including the CRC byte.
BEh
DS1822-PAR transmits up
to 9 data bytes to master.
2
Write Scratchpad
Writes data into scratchpad
bytes 2, 3, and 4 (TH, TL,
and configuration registers).
4Eh
Master transmits 3 data
bytes to DS1822-PAR.
3
Copy Scratchpad
Copies TH, TL, and
configuration register data
from the scratchpad to
EEPROM.
48h
None
1
Recall E
2
Recalls TH, TL, and
configuration register data
from EEPROM to the
scratchpad.
B8h
DS1822-PAR transmits
recall status to master.
NOTES:
1. The master must enable a strong pullup on the 1-wire bus during temperature conversions and copies
from the scratchpad to EEPROM. No other bus activity may take place during this time.
2. The master can interrupt the transmission of data at any time by issuing a reset.
3. All three bytes must be written before a reset is issued.
相關PDF資料 |
PDF描述 |
|---|---|
| DS1822Z/T&R | DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 2Cel, RECTANGULAR, SURFACE MOUNT |
| DS1822/T&R | DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 2Cel, RECTANGULAR, THROUGH HOLE MOUNT |
| DS1822 | DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 2Cel, RECTANGULAR, THROUGH HOLE MOUNT |
| DS1822+T&R | DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 2Cel, RECTANGULAR, THROUGH HOLE MOUNT |
| DS1822Z | DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 2Cel, RECTANGULAR, SURFACE MOUNT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS1822-PAR/T&R | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| DS1822-PAR_07 | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:Econo 1-Wire Parasite-Power Digital Thermometer |
| DS1822-PAR+T&R | 制造商:Maxim Integrated Products 功能描述: 制造商:Maxim Integrated Products 功能描述:TEMP SENSOR DGTL 1-WIRE 3PIN TO-92 - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC THERMOMETER ECONO DIG TO-92 制造商:Maxim Integrated Products 功能描述:Board Mount Temperature Sensors 1-Wire Digital Thermometer |
| DS1822-PAR+T&R | 功能描述:板上安裝溫度傳感器 1-Wire Digital Thermometer RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| DS-18-22-RS | 制造商:TE Connectivity 功能描述:Red sealed splice terminal,0.5-1.5sq.mm |
發布緊急采購，3分鐘左右您將得到回復。