- 您現在的位置：買賣IC網 > PDF目錄97858 > DS1243Y (MAXIM INTEGRATED PRODUCTS INC) 0 TIMER(S), REAL TIME CLOCK, PDIP28 PDF資料下載
參數資料
| 型號： | DS1243Y |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | Timer or RTC |
| 英文描述： | 0 TIMER(S), REAL TIME CLOCK, PDIP28 |
| 封裝： | 0.720 INCH, ENCAPSULATED, DIP-28 |
| 文件頁數： | 8/13頁 |
| 文件大?。?/td> | 245K |
| 代理商： | DS1243Y |
DS1243Y
4 of 13
PHANTOM CLOCK OPERATION
Communication with the Phantom Clock is established by pattern recognition on a serial bit stream of 64
bits which must be matched by executing 64 consecutive write cycles containing the proper data on DQ0.
All accesses which occur prior to recognition of the 64–bit pattern are directed to memory.
After recognition is established, the next 64 read or write cycles either extract or update data in the
Phantom Clock, and memory access is inhibited.
Data transfer to and from the timekeeping function is accomplished with a serial bit stream under control
of Chip Enable ( CE ), Output Enable ( OE ), and Write Enable ( WE ). Initially, a read cycle to any memory
location using the CE and OE control of the Phantom Clock starts the pattern recognition sequence by
moving a pointer to the first bit of the 64–bit comparison register. Next, 64 consecutive write cycles are
executed using the CE and WE control of the SmartWatch. These 64 write cycles are used only to gain
access to the Phantom Clock.
Therefore, any address to the memory in the socket is acceptable.
However, the write cycles generated to gain access to the Phantom Clock are also writing data to a
location in the mated RAM. The preferred way to manage this requirement is to set aside just one address
location in RAM as a Phantom Clock scratch pad. When the first write cycle is executed, it is compared
to bit 0 of the 64–bit comparison register. If a match is found, the pointer increments to the next location
of the comparison register and awaits the next write cycle. If a match is not found, the pointer does not
advance and all subsequent write cycles are ignored. If a read cycle occurs at any time during pattern
recognition, the present sequence is aborted and the comparison register pointer is reset. Pattern
recognition continues for a total of 64 write cycles as described above until all the bits in the comparison
register have been matched (this bit pattern is shown in Figure 1). With a correct match for 64 bits, the
Phantom Clock is enabled and data transfer to or from the timekeeping registers can proceed. The next 64
cycles will cause the Phantom Clock to either receive or transmit data on DQ0, depending on the level of
the OE pin or the WE pin. Cycles to other locations outside the memory block can be interleaved with
CE
cycles without interrupting the pattern recognition sequence or data transfer sequence to the Phantom
Clock.
PHANTOM CLOCK REGISTER INFORMATION
The Phantom Clock information is contained in 8 registers of 8 bits, each of which is sequentially
accessed 1 bit at a time after the 64–bit pattern recognition sequence has been completed. When updating
the Phantom Clock registers, each register must be handled in groups of 8 bits. Writing and reading
individual bits within a register could produce erroneous results. These read/write registers are defined in
Figure 2.
Data contained in the Phantom Clock register is in binary coded decimal format (BCD). Reading and
writing the registers is always accomplished by stepping through all 8 registers, starting with bit 0 of
register 0 and ending with bit 7 of register 7.
相關PDF資料 |
PDF描述 |
|---|---|
| DS1244W-120 | 0 TIMER(S), REAL TIME CLOCK, PDIP28 |
| DS1244YP-70 | 0 TIMER(S), REAL TIME CLOCK, DMA34 |
| DS1244WP-120 | 0 TIMER(S), REAL TIME CLOCK, DMA34 |
| DS1244Y-70 | 0 TIMER(S), REAL TIME CLOCK, PDMA28 |
| DS1244Y | 0 TIMER(S), REAL TIME CLOCK, PDIP28 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS1243Y+ | 制造商:Maxim Integrated Products 功能描述:Bulk |
| DS1243Y-120 | 功能描述:實時時鐘 64k NV SRAM w/Phantom Clock RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
| DS1243Y120+ | 制造商:Maxim Integrated Products 功能描述: |
| DS1243Y-120+ | 功能描述:實時時鐘 64k NV SRAM w/Phantom Clock RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
| DS1243Y-120+ | 制造商:Maxim Integrated Products 功能描述:IC |
發布緊急采購，3分鐘左右您將得到回復。