- 您現在的位置：買賣IC網 > PDF目錄295503 > DS1075M-60 (MAXIM INTEGRATED PRODUCTS INC) 60 MHz, OTHER CLOCK GENERATOR, PDIP8 PDF資料下載
參數資料
| 型號： | DS1075M-60 |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | XO, clock |
| 英文描述： | 60 MHz, OTHER CLOCK GENERATOR, PDIP8 |
| 封裝： | 0.300 INCH, DIP-8 |
| 文件頁數： | 18/18頁 |
| 文件大?。?/td> | 251K |
| 代理商： | DS1075M-60 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁
DS1075
9 of 18
edge of SELX and the first rising edge of the externally derived clock is t SIE . Approximate maximum
and minimum values of these parameters are:
tLOW (min) = tI/2
tLOW (max) = 3tI/2 + tElow
tSIE (min) = tI/2
tSIE (max) = 3 tI/2 + tEhigh
NOTE:
In each case there will be a small additional delay due to internal propagation delays.
POWER-DOWN CONTROL
If the PDN bit is set to “1”, the PDN / SELX pin can be used to power-down the device. If PDN is high
the device will run normally.
POWER-DOWN
If PDN is taken low a power-down sequence is initiated. The “Enabling Sequencer” is used to execute
events in the following sequence:
1. Disable OUT (same sequence as when OE is used) and reset N counters.
2. When OUT is low, switch OUT to high-impedance state.
3. Disable MCLK (and OUT0 if EN0 bit = 0), switch OUT0 to high impedance state.
4. Disable internal oscillator and OSCIN buffer.
POWER-UP
When PDN is taken to a high level the following power-up sequence occurs:
1. Enable internal oscillator and/or OSCIN buffer.
2. Set M and N to maximum values.
3. Wait approximately 256 cycles of MCLK for it to stabilize.
4. Reset M and N to programmed values.
5. Enable OUT0 (assuming EN0 bit = 0).
6. Enable OUT.
Steps 2 through 4 exist to allow the oscillator to stabilize before enabling the outputs.
相關PDF資料 |
PDF描述 |
|---|---|
| DS1233Z-10N | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO4 |
| DS1283SN | 1 TIMER(S), REAL TIME CLOCK, PDSO28 |
| DS1543W-120 | 0 TIMER(S), REAL TIME CLOCK, PDIP28 |
| DS1644L-15 | 0 TIMER(S), REAL TIME CLOCK, DSO34 |
| DS1706RESA+T&R | 3.3 and 5.0 Volt MicroMonitor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS1075M-60IND | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Oscillator/Divider |
| DS1075M-60N | 功能描述:可編程振蕩器 RoHS:否 制造商:IDT 封裝 / 箱體:5 mm x 7 mm x 1.5 mm 頻率:15.476 MHz to 866.67, 975 MHz to 1300 MHz 頻率穩定性:+/- 50 PPM 電源電壓:3.63 V 負載電容:10 pF 端接類型:SMD/SMT 輸出格式:LVPECL 最小工作溫度:- 40 C 最大工作溫度:+ 85 C 尺寸:7 mm W x 5 mm L x 1.5 mm H 封裝: |
| DS1075M-66 | 功能描述:可編程振蕩器 RoHS:否 制造商:IDT 封裝 / 箱體:5 mm x 7 mm x 1.5 mm 頻率:15.476 MHz to 866.67, 975 MHz to 1300 MHz 頻率穩定性:+/- 50 PPM 電源電壓:3.63 V 負載電容:10 pF 端接類型:SMD/SMT 輸出格式:LVPECL 最小工作溫度:- 40 C 最大工作溫度:+ 85 C 尺寸:7 mm W x 5 mm L x 1.5 mm H 封裝: |
| DS1075M-66IND | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Oscillator/Divider |
| DS1075M-66N | 功能描述:可編程振蕩器 RoHS:否 制造商:IDT 封裝 / 箱體:5 mm x 7 mm x 1.5 mm 頻率:15.476 MHz to 866.67, 975 MHz to 1300 MHz 頻率穩定性:+/- 50 PPM 電源電壓:3.63 V 負載電容:10 pF 端接類型:SMD/SMT 輸出格式:LVPECL 最小工作溫度:- 40 C 最大工作溫度:+ 85 C 尺寸:7 mm W x 5 mm L x 1.5 mm H 封裝: |
發布緊急采購，3分鐘左右您將得到回復。