- 您現在的位置：買賣IC網 > PDF目錄295503 > DS1075M-60 (MAXIM INTEGRATED PRODUCTS INC) 60 MHz, OTHER CLOCK GENERATOR, PDIP8 PDF資料下載
參數資料
| 型號： | DS1075M-60 |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | XO, clock |
| 英文描述： | 60 MHz, OTHER CLOCK GENERATOR, PDIP8 |
| 封裝： | 0.300 INCH, DIP-8 |
| 文件頁數： | 17/18頁 |
| 文件大?。?/td> | 251K |
| 代理商： | DS1075M-60 |
DS1075
8 of 18
Figure 7
Depending on the relative timing of the SELX signal and the internal clock, there may be up to one full
cycle of tI on the output after the falling edge of SELX . Then, the “l(fā)ow” time (tLOW) between output
pulses will be dependent on the relative timing between tI and tE. The time interval between the falling
edge of SELX and the first rising edge of the externally derived clock is tSIE. Approximate maximum and
minimum values of these parameters are:
tLOW (min) = tI/2
tLOW (max) = tI/2 + tE
tSIE (min) = tI/2
tSIE (max) = 3 tI/2 + tE
NOTE:
In each case there will be a small additional delay due to internal propagation delays.
FROM EXTERNAL TO INTERNAL CLOCK
This is accomplished by a low to high transition on the SELX pin. In this case the switch is level
triggered, to allow for the possibility of a clock signal not being present at OSCIN. Note therefore, that if
a constant high-level signal is applied to OSCIN it will not be possible to switch over to the internal
reference. (Level triggering was not employed for the switch from internal to external reference as this
approach is slower and the internal clock may be running at a much higher frequency than the maximum
allowed external clock rate). When SELX is high and a low level is sensed on EXTCLK, OUT0 will be
held low until a falling edge occurs on INTCLK, then the next rising edge of INTCLK will be routed
through to OUT0.
Figure 8
Depending on the relative timing of the SELX signal and the external clock, there may be up to one full tE
high period on the output after the rising edge of SELX . Then, the “l(fā)ow” time (tLOW) between output
pulses will be dependent on the relative timing between tI and tE. The time interval between the falling
相關PDF資料 |
PDF描述 |
|---|---|
| DS1233Z-10N | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO4 |
| DS1283SN | 1 TIMER(S), REAL TIME CLOCK, PDSO28 |
| DS1543W-120 | 0 TIMER(S), REAL TIME CLOCK, PDIP28 |
| DS1644L-15 | 0 TIMER(S), REAL TIME CLOCK, DSO34 |
| DS1706RESA+T&R | 3.3 and 5.0 Volt MicroMonitor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS1075M-60IND | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Oscillator/Divider |
| DS1075M-60N | 功能描述:可編程振蕩器 RoHS:否 制造商:IDT 封裝 / 箱體:5 mm x 7 mm x 1.5 mm 頻率:15.476 MHz to 866.67, 975 MHz to 1300 MHz 頻率穩定性:+/- 50 PPM 電源電壓:3.63 V 負載電容:10 pF 端接類型:SMD/SMT 輸出格式:LVPECL 最小工作溫度:- 40 C 最大工作溫度:+ 85 C 尺寸:7 mm W x 5 mm L x 1.5 mm H 封裝: |
| DS1075M-66 | 功能描述:可編程振蕩器 RoHS:否 制造商:IDT 封裝 / 箱體:5 mm x 7 mm x 1.5 mm 頻率:15.476 MHz to 866.67, 975 MHz to 1300 MHz 頻率穩定性:+/- 50 PPM 電源電壓:3.63 V 負載電容:10 pF 端接類型:SMD/SMT 輸出格式:LVPECL 最小工作溫度:- 40 C 最大工作溫度:+ 85 C 尺寸:7 mm W x 5 mm L x 1.5 mm H 封裝: |
| DS1075M-66IND | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Oscillator/Divider |
| DS1075M-66N | 功能描述:可編程振蕩器 RoHS:否 制造商:IDT 封裝 / 箱體:5 mm x 7 mm x 1.5 mm 頻率:15.476 MHz to 866.67, 975 MHz to 1300 MHz 頻率穩定性:+/- 50 PPM 電源電壓:3.63 V 負載電容:10 pF 端接類型:SMD/SMT 輸出格式:LVPECL 最小工作溫度:- 40 C 最大工作溫度:+ 85 C 尺寸:7 mm W x 5 mm L x 1.5 mm H 封裝: |
發布緊急采購，3分鐘左右您將得到回復。