- 您現在的位置：買賣IC網 > PDF目錄17142 > DEMO9RS08KA2 (Freescale Semiconductor)DEMO BOARD FOR 9RS08KA2 PDF資料下載
參數資料
| 型號： | DEMO9RS08KA2 |
| 廠商： | Freescale Semiconductor |
| 文件頁數： | 123/136頁 |
| 文件大小： | 0K |
| 描述： | DEMO BOARD FOR 9RS08KA2 |
| 產品培訓模塊： | Mechatronics USBSpyder08 Discovery Kit RS08KA2 Low-End Microcontroller Series MC9RS08KA8 Microcontroller |
| 標準包裝： | 1 |
| 系列： | RS08 |
| 類型： | MCU |
| 適用于相關產品： | MC9RS08KA2 |
| 所含物品： | 板，線纜，CD，文檔，樣品 IC |
| 產品目錄頁面： | 730 (CN2011-ZH PDF) |
| 相關產品： | MC9RS08KA2CSCRTR-ND - IC MCU 8BIT 2K FLASH 8-SOIC PC9RS08KA2PAE-ND - MCU 8BIT 2KB FLASH RS08 8-DIP PC9RS08KA2FPE-ND - MCU 8BIT 2KB FLASH RS08 6-VDFN PC9RS08KA2DWE-ND - MCU 8BIT 2KB FLASH RS08 8-SOIC MC9RS08KA2CPC-ND - IC MCU 8-BIT 2K FLASH 8-PDIP MC9RS08KA2CDB-ND - IC MCU 8-BIT 2K FLASH 6-DFN MC9RS08KA2CSC-ND - IC MCU 8-BIT 2K FLASH 8-SOIC |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁當前第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁
Analog Comparator (RS08ACMPV1)
MC9RS08KA2 Series Data Sheet, Rev. 4
Freescale Semiconductor
87
10.4
Functional Description
The analog comparator can be used to compare two analog input voltages applied to ACMP+ and ACMP–;
or it can be used to compare an analog input voltage applied to ACMP– with an internal bandgap reference
voltage. ACBGS is used to select between the bandgap reference voltage or the ACMP+ pin as the input
to the non-inverting input of the analog comparator.
The comparator output is high when the non-inverting input is greater than the inverting input, and it is
low when the non-inverting input is less than the inverting input. ACMOD is used to select the condition
which will cause ACF to be set. ACF can be set on a rising edge of the comparator output, a falling edge
of the comparator output, or either a rising or a falling edge (toggle). The comparator output can be read
directly through ACO. The comparator output can also be driven onto the ACMPO pin using ACOPE.
Table 10-2. ACMPSC Field Descriptions
Field
Description
7
ACME
Analog Comparator Module Enable — ACME enables the ACMP module.
0 ACMP not enabled.
1 ACMP is enabled.
6
ACBGS
Analog Comparator Bandgap Select — ACBGS is used to select between the internal bandgap reference
voltage or the ACMP+ pin as the non-inverting input of the analog comparator.
0 External pin ACMP+ selected as non-inverting input to comparator.
1 Internal bandgap reference voltage selected as non-inverting input to comparator.
5
ACF
Analog Comparator Flag — ACF is set when a compare event occurs. Compare events are defined by ACMOD.
ACF is cleared by writing a one to ACF.
0 Compare event has not occurred.
1 Compare event has occurred.
4
ACIE
Analog Comparator Interrupt Enable — ACIE enables the interrupt for the ACMP. When ACIE is set, an
interrupt will be asserted when ACF is set.
0 Interrupt disabled.
1 Interrupt enabled.
3
ACO
Analog Comparator Output — Reading ACO will return the current value of the analog comparator output. ACO
is reset to a 0 and will read as a 0 when the ACMP is disabled (ACME = 0).
2
ACOPE
Analog Comparator Output Pin Enable — ACOPE is used to enable the comparator output to be placed onto
the external pin, ACMPO. ACOPE will only control the pin if the ACMP is active (ACME=1).
0 Analog comparator output not available on ACMPO.
1 Analog comparator output is driven out on ACMPO.
1:0
ACMOD
Analog Comparator Mode — ACMOD selects the type of compare event which sets ACF.
00 Encoding 0 — Comparator output falling edge.
01 Encoding 1 — Comparator output rising edge.
10 Encoding 2 — Comparator output falling edge.
11 Encoding 3 — Comparator output rising or falling edge.
相關PDF資料 |
PDF描述 |
|---|---|
| VE-J1B-EZ | CONVERTER MOD DC/DC 95V 25W |
| EBC28DREH | CONN EDGECARD 56POS .100 EYELET |
| ECC35DCMN | CONN EDGECARD 70POS .100 WW |
| EBC35DCSN | CONN EDGECARD 70POS DIP .100 SLD |
| MRJ0280DD-A | C/A MRJ21/MRJ21 GBE STRT CMR 28M |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DEMO9RS08KA8 | 功能描述:開發板和工具包 - S08 / S12 DEMO BOARD FOR KA8 PRODUCT RoHS:否 產品:Development Kits 工具用于評估:MC9S12G128 核心:S12 接口類型:CAN, LIN, RS-232, USB 工作電源電壓:5 V 制造商:Freescale Semiconductor |
| DEMO9RS08KB12 | 功能描述:開發板和工具包 - S08 / S12 KB12 DEMO Board RoHS:否 產品:Development Kits 工具用于評估:MC9S12G128 核心:S12 接口類型:CAN, LIN, RS-232, USB 工作電源電壓:5 V 制造商:Freescale Semiconductor |
| DEMO9RS08KB12 | 制造商:Freescale Semiconductor 功能描述:; LEADED PROCESS COMPATIBLE:YES; PEAK RE |
| DEMO9RS08LA8 | 功能描述:開發板和工具包 - S08 / S12 DEMO BOARD FOR LA8 RoHS:否 產品:Development Kits 工具用于評估:MC9S12G128 核心:S12 接口類型:CAN, LIN, RS-232, USB 工作電源電壓:5 V 制造商:Freescale Semiconductor |
| DEMO9RS08LE4 | 功能描述:開發板和工具包 - S08 / S12 LE4 Family Demo Board RoHS:否 產品:Development Kits 工具用于評估:MC9S12G128 核心:S12 接口類型:CAN, LIN, RS-232, USB 工作電源電壓:5 V 制造商:Freescale Semiconductor |
發布緊急采購，3分鐘左右您將得到回復。