- 您現在的位置：買賣IC網 > PDF目錄17065 > DC847A (Linear Technology)BOARD DELTA SIGMA ADC LTC2446 PDF資料下載
參數資料
| 型號： | DC847A |
| 廠商： | Linear Technology |
| 文件頁數： | 3/28頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD DELTA SIGMA ADC LTC2446 |
| 軟件下載： | QuikEval System |
| 設計資源： | DC847A Design File DC847A Schematic |
| 標準包裝： | 1 |
| 系列： | QuikEval™ |
| ADC 的數量： | 1 |
| 位數： | 24 |
| 采樣率（每秒）： | 8k |
| 數據接口： | MICROWIRE?，串行，SPI? |
| 已用 IC / 零件： | LTC2446 |
| 已供物品： | 板 |
| 相關產品： | LTC2446CUHF#PBF-ND - IC ADC 24BIT 8CH HI SPEED 38QFN LTC2446IUHF#PBF-ND - IC ADC 24BIT 8CH HI SPEED 38QFN LTC2446IUHF#TRPBF-ND - IC ADC 24BIT 8CH HI SPEED 38QFN LTC2446CUHF#TRPBF-ND - IC ADC 24BIT 8CH HI SPEED 38QFN |
第1頁第2頁當前第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
LTC2446/LTC2447
11
24467fa
Serial Clock Input/Output (SCK)
The serial clock signal present on SCK (Pin 38) is used to
synchronize the data transfer. Each bit of data is shifted out
the SDO pin on the falling edge of the serial clock.
In the Internal SCK mode of operation, the SCK pin is an
output and the LTC2446/LTC2447 create their own serial
clock. In the External SCK mode of operation, the SCK pin
is used as input. The internal or external SCK mode is
selected by tying EXT (Pin 3) LOW for external SCK and
HIGH for internal SCK.
Serial Data Output (SDO)
The serial data output pin, SDO (Pin 37), provides the
result of the last conversion as a serial bit stream (MSB
first) during the data output state. In addition, the SDO pin
is used as an end of conversion indicator during the
conversion and sleep states.
When CS (Pin 36) is HIGH, the SDO driver is switched to
a high impedance state. This allows sharing the serial
interface with other devices. If CS is LOW during the
convert or sleep state, SDO will output EOC. If CS is LOW
during the conversion phase, the EOC bit appears HIGH on
the SDO pin. Once the conversion is complete, EOC goes
LOW. The device remains in the sleep state until the first
rising edge of SCK occurs while CS = LOW.
Chip Select Input (CS)
The active LOW chip select, CS (Pin 36), is used to test the
conversion status and to enable the data output transfer as
described in the previous sections.
In addition, the CS signal can be used to trigger a new
conversion cycle before the entire serial data transfer has
been completed. The LTC2446/LTC2447 will abort any
serial data transfer in progress and start a new conversion
cycle anytime a LOW-to-HIGH transition is detected at the
CS pin after the converter has entered the data output
state.
Serial Data Input (SDI)
The serial data input (SDI, Pin 34) is used to select the
speed/resolution input channel and reference of the
LTC2446/LTC2447. SDI is programmed by a serial input
data stream under the control of SCK during the data
output cycle, see Figure 3.
Initially, after powering up, the device performs a conver-
sion with IN+ = CH0, IN– = CH1, REF+ = VREF01+, REF– =
VREF01–, OSR = 256 (output rate nominally 880Hz), and 1x
speed mode (no Latency). Once this first conversion is
complete, the device enters the sleep state and is ready to
output the conversion result and receive the serial data input
stream programming the speed/resolution, input channel
and reference for the next conversion. At the conclusion of
each conversion cycle, the device enters this state.
In order to change the speed/resolution, reference or input
channel, the first 3 bits shifted into the device are 101. This
is compatible with the programming sequence of the
LTC2414/LTC2418/LTC2444/LTC2445/LTC2448/
LTC2449. If the sequence is set to 000 or 100, the follow-
ing input data is ignored (don’t care) and the previously
selected speed/resolution, channel and reference remain
valid for the next conversion. Combinations other than 101,
100, and 000 of the 3 control bits should be avoided.
If the first 3 bits shifted into the device are 101, then the
following 5 bits select the input channel/reference for the
following conversion (see Table 3). The next 5 bits select
the speed/resolution and mode 1x (no Latency) 2x (double
output rate with one conversion latency), see Table 4. If
these 5 bits are set to all 0’s, the previous speed remains
selected for the next conversion. This is useful in applica-
tions requiring a fixed output rate/resolution but need to
change the input channel or reference. In this case, the
timing and input sequence is compatible with the LTC2414/
LTC2418.
When an update operation is initiated (the first 3 bits are
101) the next 5 bits are the channel/reference address. The
first bit, SGL, determines if the input selection is differen-
tial (SGL = 0) or single-ended (SGL = 1). For SGL = 0, two
adjacent channels can be selected to form a differential
input. For SGL = 1, one of 8 channels is selected as the
positive input. The negative input is COM for all single
ended operations. The global VREF bit (GLBL) is used to
determine which reference is selected. GLBL = 0 selects
the individual reference slaved to a given channel. Each set
of channels has a corresponding differential input refer-
ence. If GLBL = 1, a global reference VREFG+/VREFG– is
selected. The global reference input may be used for any
input channel selected. Table 3 shows a summary of input/
reference selection. The remaining bits (ODD, A1, A0)
determine which channel is selected.
APPLICATIO S I FOR ATIO
WU
UU
相關PDF資料 |
PDF描述 |
|---|---|
| DC790A | BOARD DELTA SIGMA ADC LTC2439-1 |
| EVAL-AD5535EBZ | BOARD EVALUATION FOR AD5535 |
| SDR0403-390KL | INDUCTOR POWER 39UH 0.59A 0403 |
| EBA22DRMD | CONN EDGECARD 44POS .125 SQ WW |
| EVAL-AD5757SDZ | BOARD EVAL FOR AD5757 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DC850 | 制造商:Molex 功能描述: |
| DC852A | 功能描述:BOARD DEMO FOR LTC4354 RoHS:是 類別:未定義的類別 >> 其它 系列:* 標準包裝:1 系列:* 其它名稱:MS305720A |
| DC8550 | 制造商:DCCOM 制造商全稱:Dc Components 功能描述:TECHNICAL SPECIFICATIONS OF PNP EPITAXIAL PLANAR TRANSISTOR |
| DC8550S | 制造商:DCCOM 制造商全稱:Dc Components 功能描述:TECHNICAL SPECIFICATIONS OF PNP EPITAXIAL PLANAR TRANSISTOR |
| DC859A | 功能描述:EVAL BOARD FOR LTC4267 RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 標準包裝:1 系列:- 主要目的:數字電位器 嵌入式:- 已用 IC / 零件:AD5258 主要屬性:- 次要屬性:- 已供物品:板 相關產品:AD5258BRMZ1-ND - IC POT DGTL I2C1K 64P 10MSOPAD5258BRMZ10-ND - IC POT DGTL I2C 10K 64P 10MSOPAD5258BRMZ100-ND - IC POT DGTL I2C 100K 64P 10MSOPAD5258BRMZ50-ND - IC POT DGTL I2C 50K 64P 10MSOPAD5258BRMZ1-R7-ND - IC POT DGTL I2C 1K 64P 10MSOPAD5258BRMZ10-R7-ND - IC POT DGTL I2C 10K 64P 10MSOPAD5258BRMZ50-R7-ND - IC POT DGTL I2C 50K 64P 10MSOPAD5258BRMZ100-R7-ND - IC POT DGTL I2C 100K 64P 10MSOP |
發布緊急采購，3分鐘左右您將得到回復。