- 您現在的位置：買賣IC網 > PDF目錄17065 > DC790A (Linear Technology)BOARD DELTA SIGMA ADC LTC2439-1 PDF資料下載
參數資料
| 型號： | DC790A |
| 廠商： | Linear Technology |
| 文件頁數： | 25/28頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD DELTA SIGMA ADC LTC2439-1 |
| 軟件下載： | QuikEval System |
| 設計資源： | DC790A Design File DC790A Schematic |
| 標準包裝： | 1 |
| 系列： | QuikEval™ |
| ADC 的數量： | 1 |
| 位數： | 16 |
| 采樣率（每秒）： | 6.8 |
| 數據接口： | MICROWIRE?，串行，SPI? |
| 工作溫度： | 0°C ~ 70°C |
| 已用 IC / 零件： | LTC2439-1 |
| 已供物品： | 板 |
| 相關產品： | LTC2439-1CGN#PBF-ND - IC ADC 16BIT 16CH MCRPWR 28SSOP LTC2439-1IGN#PBF-ND - IC ADC 16BIT 16CH MCRPWR 28SSOP LTC2439-1CGN#TRPBF-ND - IC ADC 16BIT 16CH MCRPWR 28SSOP LTC2439-1IGN#TRPBF-ND - IC ADC 16BIT 16CH MCRPWR 28SSOP LTC2439-1CGN-ND - IC ADC 16BIT 16CH MCRPWR 28SSOP LTC2439-1IGN-ND - IC ADC 16BIT 16CH MCRPWR 28SSOP LTC2439-1IGN#TR-ND - IC ADC 16BIT 16CH MCRPWR 28SSOP LTC2439-1CGN#TR-ND - IC ADC 16BIT 16CH MCRPWR 28SSOP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁當前第25頁第26頁第27頁第28頁
LTC2439-1
6
24391fa
CH0 to CH15 (Pin 21 to Pin 28 and Pin 1 to Pin 8): Analog
Inputs. May be programmed for single-ended or differen-
tial mode.
VCC (Pin 9): Positive Supply Voltage. Bypass to GND
(Pin 15) with a 10
F tantalum capacitor in parallel with
0.1
F ceramic capacitor as close to the part as possible.
COM (Pin 10): The common negative input (IN–) for all
single-ended multiplexer configurations. The voltage on
Channel 0 to 15 and COM input pins can have any value
between GND – 0.3V and VCC + 0.3V. Within these limits,
the two selected inputs (IN+ and IN–) provide a bipolar
input range (VIN = IN+ – IN–) from – 0.5 VREF to 0.5 VREF.
Outside this input range, the converter produces unique
overrange and underrange output codes.
REF+ (Pin 11), REF– (Pin 12): Differential Reference
Input. The voltage on these pins can have any value
between GND and VCC as long as the positive reference
input, REF+, is maintained more positive than the negative
reference input, REF –, by at least 0.1V.
GND (Pin 15): Ground. Connect this pin to a ground plane
through a low impedance connection.
CS (Pin 16): Active LOW Digital Input. A LOW on this pin
enables the SDO digital output and wakes up the ADC.
Following each conversion the ADC automatically enters
the Sleep mode and remains in this low power state as
long as CS is HIGH. A LOW-to-HIGH transition on CS
during the Data Output transfer aborts the data transfer
and starts a new conversion.
SDO (Pin 17): Three-State Digital Output. During the Data
Output period, this pin is used as the serial data output.
When the chip select CS is HIGH (CS = VCC), the SDO pin
is in a high impedance state. During the Conversion and
Sleep periods, this pin is used as the conversion status
output. The conversion status can be observed by pulling
CS LOW.
SCK (Pin 18): Bidirectional Digital Clock Pin. In Internal
Serial Clock Operation mode, SCK is used as the digital
output for the internal serial interface clock during the Data
Output period. In External Serial Clock Operation mode,
SCK is used as the digital input for the external serial
interface clock during the Data Output period. A weak
internal pull-up is automatically activated in Internal Serial
Clock Operation mode. The Serial Clock Operation mode is
determined by the logic level applied to the SCK pin at
power up or during the most recent falling edge of CS.
FO (Pin 19): Frequency Control Pin. Digital input that
controls the ADC’s notch frequencies and conversion
time. When the FO pin is connected to GND (FO = 0V), the
converter uses its internal oscillator and rejects 50Hz and
60Hz simultaneously. When FO is driven by an external
clock signal with a frequency fEOSC, the converter uses this
signal as its system clock and the digital filter has 87dB
minimum rejection in the range fEOSC/2560 ±14% and
110dB minimum rejection at fEOSC/2560 ±4%.
SDI (Pin 20): Serial Digital Data Input. During the Data
Output period, this pin is used to shift in the multiplexer
address started from the first rising SCK edge. During the
Conversion and Sleep periods, this pin is in the DON’T
CARE state. However, a HIGH or LOW logic level should be
maintained on SDI in the DON’T CARE mode to avoid an
excessive current in the SDI input buffers.
NC (Pins 13, 14): Not Internally Connected. Do not con-
nect or connect to ground.
UU
U
PI FU CTIO S
相關PDF資料 |
PDF描述 |
|---|---|
| EVAL-AD5535EBZ | BOARD EVALUATION FOR AD5535 |
| SDR0403-390KL | INDUCTOR POWER 39UH 0.59A 0403 |
| EBA22DRMD | CONN EDGECARD 44POS .125 SQ WW |
| EVAL-AD5757SDZ | BOARD EVAL FOR AD5757 |
| EVAL-AD5760SDZ | BOARD EVAL FOR AD5760SDZ |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DC798B | 功能描述:BOARD DELTA SIGMA ADC LTC2480 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:QuikEval™ 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
| DC-7G3EWA | 制造商:Kingbright Corporation 功能描述:Red/Green 10-seg LED lightbar, DC-7G3EWA |
| DC7G3HWA | 功能描述:LED條和陣列 7GR 3RED BARGRAFT 10 SEGMENT RoHS:否 制造商:Avago Technologies 產品:LED Light Bars 照明顏色:Red 光強度:45 mcd 封裝:Tube |
| DC-7G3HWA | 制造商:Kingbright Corporation 功能描述: |
| DC7K67J/4LR61 | 制造商:Duracell 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。