參數資料
型號： CS4360-KZZ
廠商： Cirrus Logic Inc
文件頁數： 28/37頁
文件大?。?/td> 0K
描述： IC DAC STER 6CH 102DB 28TSSOP
標準包裝： 50
位數： 24
數據接口： 串行
轉換器數目： 6
電壓電源： 模擬和數字
功率耗散（最大）： 265mW
工作溫度： -10°C ~ 70°C
安裝類型： 表面貼裝
封裝/外殼： 28-TSSOP（0.173"，4.40mm 寬）
供應商設備封裝： 28-TSSOP
包裝： 托盤
輸出數目和類型： 6 電壓，單極
采樣率（每秒）： 192k
產品目錄頁面： 757 (CN2011-ZH PDF)
其它名稱： 598-1642
CS4360
34
DS517F2
Zero Cross
Zero Cross Enable dictates that signal level changes, either by attenuation changes or muting, will
occur on a signal zero crossing to minimize audible artifacts. The requested level change will occur
after a timeout period between 512 and 1024 sample periods (10.7 ms to 21.3 ms at 48 kHz sample
rate) if the signal does not encounter a zero crossing. The zero cross function is independently mon-
itored and implemented for each channel.
Soft Ramp
Soft Ramp allows level changes, both muting and attenuation, to be implemented by incrementally
ramping, in 1/8 dB steps, from the current level to the new level at a rate of 1 dB per 8 left/right clock
periods.
Soft Ramp and Zero Cross
Soft Ramp and Zero Cross dictates that signal level changes, either by attenuation changes or mut-
ing, will occur in 1/8 dB steps and will be implemented on successive signal zero crossings. The
1/8 dB level changes will occur after timeout periods between 512 and 1024 sample periods (10.7 ms
to 21.3 ms at 48 kHz sample rate) if the signal does not encounter zero crossings. The zero cross
function is independently monitored and implemented for each channel.
6.5.2
CONTROL PORT ENABLE (CPEN) BIT 5
Default = 0
0 - Disabled
1 - Enabled
Function:
The Control Port will become active and reset to the default settings when this function is enabled.
6.5.3
POWER DOWN (PDN) BIT 4
Default = 1
0 - Disabled
1 - Enabled
Function:
The entire device will enter a low-power state when this function is enabled, but the contents of the
control registers will be retained in this mode. The power-down bit defaults to ‘enabled’ on power-up
and must be disabled before normal operation in Control Port mode can occur.
6.5.4
POPGUARD TRANSIENT CONTROL (POPG) BIT 3
Default = 1
0 - Disabled
1 - Enabled
Function:
The PopGuard Transient Control allows the quiescent voltage to slowly ramp to and from 0 volts to
the quiescent voltage during power-on or power-off when this function is enabled. Please see section
4.6 for implementation details.
相關PDF資料
PDF描述
CS4361-CZZR IC DAC STER 6CH 105DB 20-TSSOP
CS4362-KQZ IC DAC 6CH 114DB 192KHZ 48LQFP
CS4362A-DQZ IC DAC 6CH 114DB 192KHZ 48-LQFP
CS4364-CQZR IC DAC 103DB 24BIT 6CH 48-LQFP
CS4382A-DQZ IC DAC 8CH 114DB 192KHZ 48-LQFP
相關代理商/技術參數
參數描述
CS4360-KZZR 功能描述:數模轉換器- DAC IC 102dB 24Bit 192kHz 6ch DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube
CS4361 制造商:CIRRUS 制造商全稱:Cirrus Logic 功能描述:20-Pin, 24-Bit, 192 kHz, 6-Channel D/A Converter
CS4361_08 制造商:CIRRUS 制造商全稱:Cirrus Logic 功能描述:20-Pin, 24-Bit, 192 kHz, 6-Channel D/A Converter
CS4361-CZZ 功能描述:音頻數/模轉換器 IC 6-Ch DAC 24-Bit 192kHz 105dB RoHS:否 制造商:Texas Instruments 轉換器數量: 分辨率:16 bit 接口類型:I2S, UBS 轉換速率: 信噪比:98 dB 工作電源電壓:5 V DAC 輸出端數量:2 工作溫度范圍:- 25 C to + 85 C 電源電流:23 mA 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-32 封裝:Reel
CS4361-CZZR 功能描述:數模轉換器- DAC IC 105dB 24-bit 192kHz 6ch DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*