參數資料
型號： CS4360-KZZ
廠商： Cirrus Logic Inc
文件頁數： 19/37頁
文件大?。?/td> 0K
描述： IC DAC STER 6CH 102DB 28TSSOP
標準包裝： 50
位數： 24
數據接口： 串行
轉換器數目： 6
電壓電源： 模擬和數字
功率耗散（最大）： 265mW
工作溫度： -10°C ~ 70°C
安裝類型： 表面貼裝
封裝/外殼： 28-TSSOP（0.173"，4.40mm 寬）
供應商設備封裝： 28-TSSOP
包裝： 托盤
輸出數目和類型： 6 電壓，單極
采樣率（每秒）： 192k
產品目錄頁面： 757 (CN2011-ZH PDF)
其它名稱： 598-1642
CS4360
26
DS517F2
4.9.1
Memory Address Pointer (MAP)
The MAP byte precedes the control port register byte during a write operation and is not available again
until after a start condition is initiated. During a read operation the byte transmitted after the ACK will con-
tain the data of the register pointed to by the MAP (see sections 4.9.1a and 4.9.3 for write/read details).
4.9.1a
INCR (Auto Map Increment)
The device has MAP auto increment capability enabled by the INCR bit (the MSB) of the MAP. If INCR is
set to 0, MAP will stay constant for successive IC writes or reads and SPI writes. If INCR is set to 1, MAP
will auto increment after each byte is written, allowing block reads or writes of successive registers.
Default = ‘0’
0 - Disabled
1 - Enabled
4.9.1b
MAP0-3 (Memory Address Pointer)
Default = ‘0000’
4.9.2
IC Mode
In the IC mode, data is clocked into and out of the bi-directional serial control data line, SDA, by the serial
control port clock, SCL. There is no CS pin. Pin AD0 enables the user to alter the chip address
(001000[AD0][R/W]) and should be tied to VLC or GND as required, before powering up the device. If the
device ever detects a high-to-low transition on the AD0/CS pin after power-up, SPI mode will be selected.
4.9.2a
IC Write
To write to the device, follow the procedure below while adhering to the control port Switching Specifica-
tions in section 3.
1) Initiate a START condition to the IC bus followed by the address byte. The upper 6 bits must be
001000. The seventh bit must match the setting of the AD0 pin, and the eighth must be 0. The eighth
bit of the address byte is the R/W bit.
2) Wait for an acknowledge (ACK) from the device, then write to the memory address pointer, MAP. This
byte points to the register to be written.
3) Wait for an acknowledge (ACK) from the device, then write the desired data to the register pointed to
by the MAP.
4) If the INCR bit (see section 4.9.1a) is set to 1, repeat the previous step until all the desired registers
are written, then initiate a STOP condition to the bus.
5) If the INCR bit is set to 0 and further IC writes to other registers are desired, it is necessary to repeat
the procedure detailed from step 1. If no further writes to other registers are desired, initiate a STOP
condition to the bus.
76543
210
INCR
Reserved
MAP3
MAP2
MAP1
MAP0
00000
000
相關PDF資料
PDF描述
CS4361-CZZR IC DAC STER 6CH 105DB 20-TSSOP
CS4362-KQZ IC DAC 6CH 114DB 192KHZ 48LQFP
CS4362A-DQZ IC DAC 6CH 114DB 192KHZ 48-LQFP
CS4364-CQZR IC DAC 103DB 24BIT 6CH 48-LQFP
CS4382A-DQZ IC DAC 8CH 114DB 192KHZ 48-LQFP
相關代理商/技術參數
參數描述
CS4360-KZZR 功能描述:數模轉換器- DAC IC 102dB 24Bit 192kHz 6ch DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube
CS4361 制造商:CIRRUS 制造商全稱:Cirrus Logic 功能描述:20-Pin, 24-Bit, 192 kHz, 6-Channel D/A Converter
CS4361_08 制造商:CIRRUS 制造商全稱:Cirrus Logic 功能描述:20-Pin, 24-Bit, 192 kHz, 6-Channel D/A Converter
CS4361-CZZ 功能描述:音頻數/模轉換器 IC 6-Ch DAC 24-Bit 192kHz 105dB RoHS:否 制造商:Texas Instruments 轉換器數量: 分辨率:16 bit 接口類型:I2S, UBS 轉換速率: 信噪比:98 dB 工作電源電壓:5 V DAC 輸出端數量:2 工作溫度范圍:- 25 C to + 85 C 電源電流:23 mA 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-32 封裝:Reel
CS4361-CZZR 功能描述:數模轉換器- DAC IC 105dB 24-bit 192kHz 6ch DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*