- 您現在的位置：買賣IC網 > PDF目錄1908 > CAT9534HV4I-GT2 (ON Semiconductor)IC I/O EXPANDER 8BIT 16-TQFN PDF資料下載
參數資料
| 型號： | CAT9534HV4I-GT2 |
| 廠商： | ON Semiconductor |
| 文件頁數： | 13/14頁 |
| 文件大小： | 0K |
| 描述： | IC I/O EXPANDER 8BIT 16-TQFN |
| 標準包裝： | 2,000 |
| 接口： | I²C，SM 總線 |
| 輸入/輸出數： | 8 |
| 中斷輸出： | 是 |
| 頻率 - 時鐘： | 400kHz |
| 電源電壓： | 2.3 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-WQFN 裸露焊盤 |
| 供應商設備封裝： | 16-TQFN（4x4） |
| 包裝： | 帶卷 (TR) |
| 包括： | POR |
CAT9534
http://onsemi.com
8
Acknowledge
After a successful data transfer, each receiving device is
required to generate an acknowledge. The acknowledging
device pulls down the SDA line during the ninth clock cycle,
signaling that it received the 8 bits of data. The SDA line
remains stable LOW during the HIGH period of the
acknowledge related clock pulse (Figure 6).
The CAT9534 responds with an acknowledge after
receiving a START condition and its slave address. If the
device has been selected along with a write operation, it
responds with an acknowledge after receiving each 8bit
byte.
When the CAT9534 begins a READ mode it transmits 8
bits of data, releases the SDA line, and monitors the line for
an acknowledge. Once it receives this acknowledge, the
CAT9534 will continue to transmit data. If no acknowledge
is sent by the Master, the device terminates data transmission
and waits for a STOP condition. The master must then issue
a STOP condition to return the CAT9534 to the standby
power mode and place the device in a known state.
Registers and Bus Transactions
The CAT9534 consists of an input port register, an output
port register, a polarity inversion register and a
configuration register. Table 7 shows the register address
information.
Table 7. REGISTER COMMAND BYTE
Command
(hex)
Protocol
Function
0x00
Read byte
Input port register
0x01
Read/write byte
Output port register
0x02
Read/write byte
Polarity inversion register
0x03
Read/write byte
Configuration register
The command byte is the first byte to follow the device
address byte during a write/read bus transaction. The
register command byte acts as a pointer to determine which
register will be written or read.
The input port register is a read only port. It reflects the
incoming logic levels of the I/O pins, regardless of whether
the pin is defined as an input or an output by the
configuration register. Writes to the input port register are
ignored.
Table 8. REGISTER 0 – INPUT PORT REGISTER
bit
I7
I6
I5
I4
I3
I2
I1
I0
default
1
Table 9. REGISTER 1 – OUTPUT PORT REGISTER
bit
O7
O6
O5
O4
O3
O2
O1
O0
default
1
Table 10. REGISTER 2 –
POLARITY INVERSION REGISTER
bit
N7
N6
N5
N4
N3
N2
N1
N0
default
0
Table 11. REGISTER 3 – CONFIGURATION REGISTER
bit
C7
C6
C5
C4
C3
C2
C1
C0
default
1
Figure 8. Acknowledge Timing
18
9
START
SCL FROM
MASTER
BUS RELEASE DELAY (TRANSMITTER)
ACK DELAY
ACK SETUP
BUS RELEASE DELAY (RECEIVER)
DATA OUTPUT
FROM TRANSMITTER
DATA OUTPUT
FROM RECEIVER
相關PDF資料 |
PDF描述 |
|---|---|
| CAT9554AHV4I-GT2 | IC I/O EXPANDER I2C SMBUS 16TQFN |
| CAT9554AHV4I-T2 | IC I/O EXPANDER I2C/SMBUS 16TQFN |
| CAT9555HV6I-G | IC I/O EXPANDER 16BI 2C 24TQFN |
| CC-2401K2A-CS | MODEM 2400BAUD SECURE 3.3V |
| CC-2434K2-CS5 | MODEM FAX 33K 5V |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CAT9534HV4I-GT2-CUT TAPE | 制造商:ON 功能描述:CAT9534 Series 2.3 to 5.5 V 8-bit 8 I/O I? and SMBus I/O Port - TQFN-16 |
| CAT9534WI-GT2 | 功能描述:接口-I/O擴展器 8B I2C &SMBus I/O PORT RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel |
| CAT9534YI-G | 制造商:Catalyst Semiconductor 功能描述: |
| CAT9534YI-GT2 | 功能描述:接口-I/O擴展器 8B I2C &SMBus I/O PORT RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel |
| CAT9552HV6GI | 制造商:Rochester Electronics LLC 功能描述: 制造商:Catalyst Semiconductor 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。