- 您現在的位置：買賣IC網 > PDF目錄1903 > AT89C4051-24SJ (Atmel)IC MCU 4K FLASH 24MHZ 20-SOIC PDF資料下載
參數資料
| 型號： | AT89C4051-24SJ |
| 廠商： | Atmel |
| 文件頁數： | 19/19頁 |
| 文件大小： | 0K |
| 描述： | IC MCU 4K FLASH 24MHZ 20-SOIC |
| 標準包裝： | 37 |
| 系列： | 89C |
| 核心處理器： | 8051 |
| 芯體尺寸： | 8-位 |
| 速度： | 24MHz |
| 連通性： | UART/USART |
| 外圍設備： | 欠壓檢測/復位，LED，POR |
| 輸入/輸出數： | 15 |
| 程序存儲器容量： | 4KB（4K x 8） |
| 程序存儲器類型： | 閃存 |
| RAM 容量： | 128 x 8 |
| 電壓 - 電源 (Vcc/Vdd)： | 4 V ~ 6 V |
| 振蕩器型： | 內部 |
| 工作溫度： | -40°C ~ 85°C |
| 封裝/外殼： | 20-SOIC（0.295"，7.50mm 寬） |
| 包裝： | 管件 |
9
1001F–MICRO–6/08
AT89C4051
Program Verify: If lock bits LB1 and LB2 have not been programmed code data can be read
back via the data lines for verification:
1.
Reset the internal address counter to 000H by bringing RST from “L” to “H”.
2.
Apply the appropriate control signals for Read Code data and read the output data at
the port P1 pins.
3.
Pulse pin XTAL1 once to advance the internal address counter.
4.
Read the next code data byte at the port P1 pins.
5.
Repeat steps 3 and 4 until the entire array is read.
The lock bits cannot be verified directly. Verification of the lock bits is achieved by observing that
their features are enabled.
Chip Erase: The entire PEROM array (4K bytes) and the two Lock Bits are erased electrically
by using the proper combination of control signals and by holding P3.2 low for 10 ms. The code
array is written with all “1”s in the Chip Erase operation and must be executed before any non-
blank memory byte can be re-programmed.
Reading the Signature Bytes: The signature bytes are read by the same procedure as a nor-
mal verification of locations 000H, 001H, and 002H, except that P3.5 and P3.7 must be pulled to
a logic low. The values returned are as follows.
(000H) = 1EH indicates manufactured by Atmel
(001H) = 41H indicates AT89C4051
13. Programming Interface
Every code byte in the Flash array can be written and the entire array can be erased by using
the appropriate combination of control signals. The write operation cycle is self-timed and once
initiated, will automatically time itself to completion.
Most major worldwide programming vendors offer support for the Atmel AT89 microcontroller
series. Please contact your local programming vendor for the appropriate software revision.
Notes:
1. The internal PEROM address counter is reset to 000H on the rising edge of RST and is advanced by a positive pulse at
XTAL1 pin.
2. Chip Erase requires a 10-ms PROG pulse.
3. P3.1 is pulled Low during programming to indicate RDY/BSY.
13.1
Flash Programming Modes
Mode
RST/V
PP
P3.2/PROG
P3.3
P3.4
P3.5
P3.7
Write Code Data(1)(3)
12V
L
H
Read Code Data(1)
HH
L
H
Write Lock
Bit - 1
12V
HH
Bit - 2
12V
H
L
Chip Erase
12V
H
L
Read Signature Byte
H
L
(2)
相關PDF資料 |
PDF描述 |
|---|---|
| AT89C51-24PI | IC MICRO CTRL 24MHZ 40DIP |
| AT89C5130A-PUTUM | IC 8051 MCU FLASH 16K USB 32QFN |
| AT89C5131A-PUTIM | IC 8051 MCU FLASH 32K USB 32QFN |
| AT89C5131A-TISIL | IC 8051 MCU FLASH 32K USB 28SOIC |
| AT89C5132-RORUL | MCU 8051 FLASH USB 80TQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AT89C4051-24SU | 功能描述:8位微控制器 -MCU 8051 4K FLASH 2.7 TO 5.5V 24MHZ 4V-5.5V RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| AT89C4051-24SU SL383 | 制造商:Atmel Corporation 功能描述:8051 4K FLASH 2.7 TO 5.5V, PDI |
| AT89C51 | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:8-bit Microcontroller with 4K Bytes Flash |
| AT89C51_00 | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:8-bit Microcontroller with 4K Bytes Flash |
| AT89C51-12 | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:8-Bit Microcontroller with 4K Bytes Flash |
發布緊急采購，3分鐘左右您將得到回復。