參數資料
型號： AM49LV128BML11NS
廠商： SPANSION LLC
元件分類： 存儲器
英文描述： 128 Megabit (8 M x 16-Bit) MirrorBit⑩ Uniform Sector Flash Memory and 32 Mbit (2 M x 16-Bit)
中文描述： SPECIALTY MEMORY CIRCUIT, PBGA64
封裝： 12 X 9 MM, FBGA-64
文件頁數： 37/98頁
文件大?。?/td> 1016K
代理商： AM49LV128BML11NS
June 17, 2004
Am49LV128BM
35
Reading Toggle Bits DQ6/DQ2
Refer to Figure 9 for the following discussion. When-
ever the system initially begins reading toggle bit sta-
tus, it must read DQ7–DQ0 at least twice in a row to
determine whether a toggle bit is toggling. Typically,
the system would note and store the value of the tog-
gle bit after the first read. After the second read, the
system would compare the new value of the toggle bit
with the first. If the toggle bit is not toggling, the device
has completed the program or erase operation. The
system can read array data on DQ7–DQ0 on the fol-
lowing read cycle.
However, if after the initial two read cycles, the system
determines that the toggle bit is still toggling, the sys-
tem also should note whether the value of DQ5 is high
(see the section on DQ5). If it is, the system should
then determine again whether the toggle bit is tog-
gling, since the toggle bit may have stopped toggling
just as DQ5 went high. If the toggle bit is no longer
toggling, the device has successfully completed the
program or erase operation. If it is still toggling, the de-
vice did not completed the operation successfully, and
the system must write the reset command to return to
reading array data.
The remaining scenario is that the system initially de-
termines that the toggle bit is toggling and DQ5 has
not gone high. The system may continue to monitor
the toggle bit and DQ5 through successive read cy-
cles, determining the status as described in the previ-
ous paragraph. Alternatively, it may choose to perform
other system tasks. In this case, the system must start
at the beginning of the algorithm when it returns to de-
termine the status of the operation (top of Figure 9).
DQ5: Exceeded Timing Limits
DQ5 indicates whether the program, erase, or write-
to-buffer time has exceeded a specified internal pulse
count limit. Under these conditions DQ5 produces a “1,” in-
dicating that the program or erase cycle was not success-
fully completed.
The device may output a “1” on DQ5 if the system tries
to program a “1” to a location that was previously pro-
grammed to “0.”
Only an erase operation can
change a “0” back to a “1.”
Under this condition, the
device halts the operation, and when the timing limit
has been exceeded, DQ5 produces a “1.”
In all these cases, the system must write the reset
command (or the Unlock Bypass Reset command if in
Unlock Bypass mode) to return the device to the read-
ing the array (or to erase-suspend-read if the device
was previously in the erase-suspend-program mode).
DQ3: Sector Erase Timer
After writing a sector erase command sequence, the
system may read DQ3 to determine whether or not
erasure has begun. (The sector erase timer does not
apply to the chip erase command.) If additional
sectors are selected for erasure, the entire time-out
also applies after each additional sector erase com-
mand. When the time-out period is complete, DQ3
switches from a “0” to a “1.” If the time between addi-
tional sector erase commands from the system can be
assumed to be less than 50 μs, the system need not
monitor DQ3. See also the Sector Erase Command
Sequence section.
After the sector erase command is written, the system
should read the status of DQ7 (Data# Polling) or DQ6
(Toggle Bit I) to ensure that the device has accepted
the command sequence, and then read DQ3. If DQ3 is
“1,” the Embedded Erase algorithm has begun; all fur-
ther commands (except Erase Suspend) are ignored
until the erase operation is complete. If DQ3 is “0,” the
device will accept additional sector erase commands.
To ensure the command has been accepted, the sys-
tem software should check the status of DQ3 prior to
and following each subsequent sector erase com-
mand. If DQ3 is high on the second status check, the
last command might not have been accepted.
Table 10 shows the status of DQ3 relative to the other
status bits.
DQ1: Write-to-Buffer Abort
DQ1 indicates whether a Write-to-Buffer operation
was aborted. Under these conditions DQ1 produces a
“1”. The system must issue the Write-to-Buffer-Abort-
Reset command sequence to return the device to
reading array data. See Write Buffer Programming
section for more details.
相關PDF資料
PDF描述
AM49LV128BML11NT 128 Megabit (8 M x 16-Bit) MirrorBit⑩ Uniform Sector Flash Memory and 32 Mbit (2 M x 16-Bit)
AM49LV128BML15NS 128 Megabit (8 M x 16-Bit) MirrorBit⑩ Uniform Sector Flash Memory and 32 Mbit (2 M x 16-Bit)
AM49LV128BML15NT 128 Megabit (8 M x 16-Bit) MirrorBit⑩ Uniform Sector Flash Memory and 32 Mbit (2 M x 16-Bit)
AM49LV6408M Stacked Multi-chip Package (MCP) 64 Mbit (4 M x 16 bit) Flash Memory and 8 Mbit (512K x 16-Bit)
AM49LV6408MB10IT Stacked Multi-chip Package (MCP) 64 Mbit (4 M x 16 bit) Flash Memory and 8 Mbit (512K x 16-Bit)
相關代理商/技術參數
參數描述
AM49LV128BML11NT 制造商:SPANSION 制造商全稱:SPANSION 功能描述:128 Megabit (8 M x 16-Bit) MirrorBit⑩ Uniform Sector Flash Memory and 32 Mbit (2 M x 16-Bit)
AM49LV128BML15NS 制造商:SPANSION 制造商全稱:SPANSION 功能描述:128 Megabit (8 M x 16-Bit) MirrorBit⑩ Uniform Sector Flash Memory and 32 Mbit (2 M x 16-Bit)
AM49LV128BML15NT 制造商:SPANSION 制造商全稱:SPANSION 功能描述:128 Megabit (8 M x 16-Bit) MirrorBit⑩ Uniform Sector Flash Memory and 32 Mbit (2 M x 16-Bit)
AM49LV4608M 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Stacked Multi-chip Package (MCP) 64 Mbit (4 M x 16 bit) Flash Memory and 8 Mbit (512K x 16-Bit) pseudo Static RAM
AM49LV4608MB10IS 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Stacked Multi-chip Package (MCP) 64 Mbit (4 M x 16 bit) Flash Memory and 8 Mbit (512K x 16-Bit) pseudo Static RAM
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*