- 您現在的位置：買賣IC網 > PDF目錄375307 > AM49LV128BML11NS (SPANSION LLC) 128 Megabit (8 M x 16-Bit) MirrorBit⑩ Uniform Sector Flash Memory and 32 Mbit (2 M x 16-Bit) PDF資料下載
參數資料
| 型號： | AM49LV128BML11NS |
| 廠商： | SPANSION LLC |
| 元件分類： | 存儲器 |
| 英文描述： | 128 Megabit (8 M x 16-Bit) MirrorBit⑩ Uniform Sector Flash Memory and 32 Mbit (2 M x 16-Bit) |
| 中文描述： | SPECIALTY MEMORY CIRCUIT, PBGA64 |
| 封裝： | 12 X 9 MM, FBGA-64 |
| 文件頁數： | 31/98頁 |
| 文件大小： | 1016K |
| 代理商： | AM49LV128BML11NS |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁當前第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁
June 17, 2004
Am49LV128BM
29
Figure 4.
Program Operation
Program Suspend/Program Resume
Command Sequence
The Program Suspend command allows the system to
interrupt a programming operation or a Write to Buffer
programming operation so that data can be read from
any non-suspended sector. Within the suspended sec-
tor, data may be read from addresses outside of the
page (for example, Amax–A4) being programmed.
When the Program Suspend command is written dur-
ing a programming process, the device halts the pro-
gram operation within 15 μs maximum (5 μs typical)
and updates the status bits. Addresses are not re-
quired when writing the Program Suspend command.
After the programming operation has been sus-
pended, the system can read array data from any non-
suspended sector or from selected addresses within
the suspended sector (see previous paragraph). The
Program Suspend command may also be issued dur-
ing a programming operation while an erase is sus-
pended. In this case, data may be read from any
sectors not in Erase Suspend or Program Suspend. If
a read is needed from the SecSi Sector area (One-
time Program area), then the user must use the proper
command sequences to enter and exit this region.
The system may also write the autoselect command
sequence when the device is in the Program Suspend
mode. The system can read as many autoselect
codes as required. When the device exits the autose-
lect mode, the device reverts to the Program Suspend
mode, and is ready for another valid operation. See
Autoselect Command Sequence for more information.
After the Program Resume command is written, the
device reverts to programming. The system can deter-
mine the status of the program operation using the
DQ7 or DQ6 status bits, just as in the standard pro-
gram operation. See Write Operation Status for more
information.
The system must write the Program Resume com-
mand (address bits are don’t care) to exit the Program
Suspend mode and continue the programming opera-
tion. Further writes of the Resume command are ig-
nored. Another Program Suspend command can be
written after the device has resume programming.
There is no time-out limit for the Program Suspend
command. After the Program Suspend command is
written, the device will stay in Program Suspend mode
until the Program Resume command or the RESET
command/operation is written.
START
Write Program
Command Sequence
Data Poll
from System
Verify Data
No
Yes
Last Address
No
Yes
Programming
Completed
Increment Address
Embedded
Program
algorithm
in progress
Note:
See Tables 9 and 10 for program command
sequence.
Program Operation
or Write-to-Buffer
Sequence in Progress
Write Program Suspend
Command Sequence
Command is also valid for
Erase-suspended-program
operations
Autoselect and SecSi Sector
read operations are also allowed
Data cannot be read from erase- or
program-suspended sectors
Write Program Resume
Command Sequence
Read data as
required
Done
reading
No
Yes
Write address/data
XXXh/30h
Device reverts to
operation prior to
Program Suspend
Write address/data
XXXh/B0h
Wait 15 μs
相關PDF資料 |
PDF描述 |
|---|---|
| AM49LV128BML11NT | 128 Megabit (8 M x 16-Bit) MirrorBit⑩ Uniform Sector Flash Memory and 32 Mbit (2 M x 16-Bit) |
| AM49LV128BML15NS | 128 Megabit (8 M x 16-Bit) MirrorBit⑩ Uniform Sector Flash Memory and 32 Mbit (2 M x 16-Bit) |
| AM49LV128BML15NT | 128 Megabit (8 M x 16-Bit) MirrorBit⑩ Uniform Sector Flash Memory and 32 Mbit (2 M x 16-Bit) |
| AM49LV6408M | Stacked Multi-chip Package (MCP) 64 Mbit (4 M x 16 bit) Flash Memory and 8 Mbit (512K x 16-Bit) |
| AM49LV6408MB10IT | Stacked Multi-chip Package (MCP) 64 Mbit (4 M x 16 bit) Flash Memory and 8 Mbit (512K x 16-Bit) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AM49LV128BML11NT | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:128 Megabit (8 M x 16-Bit) MirrorBit⑩ Uniform Sector Flash Memory and 32 Mbit (2 M x 16-Bit) |
| AM49LV128BML15NS | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:128 Megabit (8 M x 16-Bit) MirrorBit⑩ Uniform Sector Flash Memory and 32 Mbit (2 M x 16-Bit) |
| AM49LV128BML15NT | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:128 Megabit (8 M x 16-Bit) MirrorBit⑩ Uniform Sector Flash Memory and 32 Mbit (2 M x 16-Bit) |
| AM49LV4608M | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Stacked Multi-chip Package (MCP) 64 Mbit (4 M x 16 bit) Flash Memory and 8 Mbit (512K x 16-Bit) pseudo Static RAM |
| AM49LV4608MB10IS | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Stacked Multi-chip Package (MCP) 64 Mbit (4 M x 16 bit) Flash Memory and 8 Mbit (512K x 16-Bit) pseudo Static RAM |
發布緊急采購，3分鐘左右您將得到回復。