參數資料
型號： ADV7180BSTZ
廠商： ANALOG DEVICES INC
元件分類： 顏色信號轉換
英文描述： 10-Bit, 4 x Oversampling SDTV Video Decoder
中文描述： COLOR SIGNAL DECODER, PQFP64
封裝： 10 X 10 MM, ROHS COMPLIANT, MS-026BCD, LQFP-64
文件頁數： 42/112頁
文件大?。?/td> 1320K
代理商： ADV7180BSTZ
ADV7180
BL_C_VBI, Blank Chroma During VBI, Address 0x04 [2]
Setting BL_C_VBI high, blanks the Cr and Cb values of all VBI
lines. This is done so any data that may arrive during VBI is not
decoded as color and is output through Cr and Cb. As a result,
it is possible to send VBI lines into the decoder, and then output
them through an encoder again, undistorted. Without this
blanking, any color that is incorrectly decoded would be
encoded by the video encoder, thus distorting the VBI lines.
Setting BL_C_VBI to 0 decodes and outputs color during VBI.
Setting BL_C_VBI to 1 (default) blanks Cr and Cb values
during VBI.
RANGE, Range Selection, Address 0x04 [0]
AV codes (as per ITU-R BT.656, formerly known as CCIR-656)
consist of a fixed header made up of 0xFF and 0x00 values.
These two values are reserved and therefore are not to be used
for active video. Additionally, the ITU specifies that the
nominal range for video should be restricted to values between
16 to 235 for luma and 16 to 240 for chroma.
The RANGE bit allows the user to limit the range of values
output by the ADV7180 to the recommended value range. In
any case, it ensures that the reserved values of 255d (0xFF) and
00d (0x00) are not presented on the output pins unless they are
part of an AV code header.
Rev. A | Page 42 of 112
Table 57. RANGE Function
RANGE
0
1 (default)
Description
16 ≤ Y ≤ 235
1 ≤ Y ≤ 254
16 ≤ C/P ≤ 240
1 ≤ C/P ≤ 254
AUTO_PDC_EN, Automatic Programmed Delay Control,
Address 0x27 [6]
Enabling AUTO_PDC_EN activates a function within the
ADV7180 that automatically programs the LTA[1:0] and
CTA[2:0] to have the chroma and luma data match delays for
all modes of operation. If set, manual registers LTA[1:0] and
CTA[2:0] are not used. If the automatic mode is disabled (by
setting the AUTO_PDC_EN bit to 0), the values programmed
into LTA[1:0] and CTA[2:0] registers become active.
When AUTO_PDC_EN is 0, the ADV7180 uses the LTA[1:0] and
CTA[2:0] values for delaying luma and chroma samples. Refer to
the LTA[1:0], Luma Timing Adjust, Address 0x27 [1:0] section
and the CTA[2:0], Chroma Timing Adjust, Address 0x27 [5:3]
section.
When AUTO_PDC_EN is 1 (default), the ADV7180 automati-
cally determines the LTA and CTA values to have luma and
chroma aligned at the output.
LTA[1:0], Luma Timing Adjust, Address 0x27 [1:0]
The luma timing adjust register allows the user to specify a
timing difference between chroma and luma samples.
Note that there is a certain functionality overlap with the
CTA[2:0] register. For manual programming, use the
following defaults:
CVBS input LTA[1:0] = 00
Y/C input LTA[1:0] = 01
YPrPb input LTA[1:0] = 01
Table 58. LTA Function
LTA[1:0]
00 (default)
01
10
11
Description
No delay
Luma 1 clock (37 ns) late
Luma 2 clock (74 ns) early
Luma 1 clock (37 ns) early
CTA[2:0], Chroma Timing Adjust, Address 0x27 [5:3]
The chroma timing adjust register allows the user to specify a
timing difference between chroma and luma samples. This may
be used to compensate for external filter group delay differences
in the luma vs. chroma path and to allow a different number of
pipeline delays while processing the video downstream. Review
this functionality together with the LTA[1:0] register.
The chroma can be delayed or advanced only in chroma pixel
steps. One chroma pixel step is equal to two luma pixels. The
programmable delay occurs after demodulation, where one can
no longer delay by luma pixel steps.
For manual programming, use the following defaults:
CVBS input CTA[2:0] = 011
Y/C input CTA[2:0] = 101
YPrPb input CTA[2:0] = 110
Table 59. CTA Function
CTA[2:0]
000
001
010
011 (default)
100
101
110
111
Description
Not used
Chroma + 2 chroma pixel (early)
Chroma + 1 chroma pixel (early)
No delay
Chroma – 1 chroma pixel (late)
Chroma – 2 chroma pixel (late)
Chroma – 3 chroma pixel (late)
Not used
相關PDF資料
PDF描述
ADV7181 Multiformat SDTV Video Decoder
ADV7181B Multiformat SDTV Video Decoder
ADV7181BBCPZ Multiformat SDTV Video Decoder
ADV7181BBSTZ Multiformat SDTV Video Decoder
ADV7181BCP Multiformat SDTV Video Decoder
相關代理商/技術參數
參數描述
ADV7180BSTZ 制造商:Analog Devices 功能描述:Video IC
ADV7180BSTZ-REEL 功能描述:IC VIDEO DECODER SDTV 64-LQFP RoHS:是 類別:集成電路 (IC) >> 線性 - 視頻處理 系列:- 標準包裝:250 系列:- 類型:電平移位器 應用:LCD 電視機/監控器 安裝類型:表面貼裝 封裝/外殼:28-WFQFN 裸露焊盤 供應商設備封裝:28-WQFN（4x4）裸露焊盤 包裝:帶卷 (TR) 其它名稱:296-32523-2TPS65198RUYT-ND
ADV7180KCP32Z 功能描述:IC VIDEO DECODER 10BIT 32LFCSP RoHS:是 類別:集成電路 (IC) >> 線性 - 視頻處理 系列:- 產品變化通告:Product Discontinuation 07/Mar/2011 標準包裝:3,000 系列:OMNITUNE™ 類型:調諧器 應用:移動電話，手機，視頻顯示器 安裝類型:表面貼裝 封裝/外殼:65-WFBGA 供應商設備封裝:PG-WFSGA-65 包裝:帶卷 (TR) 其它名稱:SP000365064
ADV7180KCP32Z-RL 功能描述:IC VIDEO DECODER 10BIT 32LFCSP RoHS:是 類別:集成電路 (IC) >> 線性 - 視頻處理 系列:- 產品變化通告:Product Discontinuation 07/Mar/2011 標準包裝:3,000 系列:OMNITUNE™ 類型:調諧器 應用:移動電話，手機，視頻顯示器 安裝類型:表面貼裝 封裝/外殼:65-WFBGA 供應商設備封裝:PG-WFSGA-65 包裝:帶卷 (TR) 其它名稱:SP000365064
ADV7180KST48Z 功能描述:IC VID DECOD SDTV 10BIT 48LQFP RoHS:是 類別:集成電路 (IC) >> 線性 - 視頻處理 系列:- 產品變化通告:Product Discontinuation 07/Mar/2011 標準包裝:3,000 系列:OMNITUNE™ 類型:調諧器 應用:移動電話，手機，視頻顯示器 安裝類型:表面貼裝 封裝/外殼:65-WFBGA 供應商設備封裝:PG-WFSGA-65 包裝:帶卷 (TR) 其它名稱:SP000365064
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*