- 您現在的位置：買賣IC網 > PDF目錄10616 > ADV7180BST48Z (Analog Devices Inc)IC VID DECOD SDTV 10BIT 48LQFP PDF資料下載
參數資料
| 型號： | ADV7180BST48Z |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 70/116頁 |
| 文件大小： | 0K |
| 描述： | IC VID DECOD SDTV 10BIT 48LQFP |
| 標準包裝： | 1 |
| 類型： | 視頻解碼器 |
| 應用： | 數碼相機，手機，便攜式視頻 |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 48-LQFP |
| 供應商設備封裝： | 48-LQFP（7x7） |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁當前第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁
Data Sheet
ADV7180
Rev. I | Page 57 of 116
VDP_TTXT_TYPE_MAN_ENABLE, Enable Manual
Selection of Teletext Type, Address 0x60[2], User Sub Map
Setting VDP_TTXT_TYPE_MAN_ENABLE to 0 (default), the
manual programming of the teletext type is disabled.
Setting VDP_TTXT_TYPE_MAN_ENABLE to 1, the manual
programming of the teletext type is enabled.
VDP_TTXT_TYPE_MAN[1:0], Specify the Teletext Type,
Address 0x60[1:0], User Sub Map
These bits specify the teletext type to be decoded. These bits are
functional only if VDP_TTXT_TYPE_MAN_ENABLE is set to 1.
Table 72. VDP_TTXT_TYPE_MAN Function
VDP_TTXT_
TYPE_MAN[1:0]
625/50 (PAL)
525/60 (NTSC)
00 (default)
Teletext-ITU-BT.653-
625/50-A
Reserved
01
Teletext-ITU-BT.653-
625/50-B (WST)
Teletext-ITU-BT.653-
525/60-B
10
Teletext-ITU-BT.653-
625/50-C
Teletext-ITU-BT.653-
525/60-C or EIA516
(NABTS)
11
Teletext-ITU-BT.653-
625/50-D
Teletext-ITU-BT.653-
525/60-D
VDP Ancillary Data Output
Reading the data back via I2C may not be feasible for VBI data
standards with high data rates (for example, teletext). An alternative
is to place the sliced data in a packet in the line blanking of the
digital output CCIR656 stream. This is available for all standards
sliced by the VDP module.
When data is sliced on a given line, the corresponding ancillary
data packet is placed immediately after the next EAV code that
occurs at the output (that is, data sliced from multiple lines are
not buffered up and then emitted in a burst). Note that, due to
the vertical delay through the comb filters, the line number on
which the packet is placed differs from the line number on
which the data was sliced.
The user can enable or disable the insertion of VDP results that
have been decoded into the 656 ancillary streams by using the
ADF_ENABLE bit.
ADF_ENABLE, Enable Ancillary Data Output Through
656 Stream, Address 0x62[7], User Sub Map
Setting ADF_ENABLE to 0 (default) disables the insertion of
VBI decoded data into the ancillary 656 stream.
Setting ADF_ENABLE to 1 enables the insertion of VBI
decoded data into the ancillary 656 stream.
The user may select the data identification word (DID) and the
secondary data identification word (SDID) through programming
the ADF_DID[4:0] and ADF_SDID[5:0] bits, respectively.
ADF_DID[4:0], User-Specified Data ID Word in Ancillary
Data, Address 0x62[4:0], User Sub Map
This bit selects the data ID word to be inserted into the ancillary
data stream with the data decoded by the VDP.
The default value of ADF_DID[4:0] is 10101.
ADF_SDID[5:0], User-Specified Secondary Data ID Word
in Ancillary Data, Address 0x63[5:0], User Sub Map
These bits select the secondary data ID word to be inserted in
the ancillary data stream with the data decoded by the VDP.
The default value of ADF_SDID[5:0] is 101010.
DUPLICATE_ADF, Enable Duplication/Spreading of
Ancillary Data over Y and C Buses, Address 0x63[7], User
Sub Map
This bit determines whether the ancillary data is duplicated over
both Y and C buses or if the data packets are spread between
the two channels.
When DUPLICATE_ADF to 0 (default) is set, the ancillary data
packet is spread across the Y and C data streams.
When DUPLICATE_ADF to 1 is set, the ancillary data packet is
duplicated on the Y and C data streams.
ADF_MODE[1:0], Determine the Ancillary Data Output
Mode, Address 0x62[6:5], User Sub Map
These bits determine whether the ancillary data output mode is
in byte mode or nibble mode.
Table 73. ADF_MODE
ADF_MODE[1:0]
Description
00 (default)
Nibble mode
01
Byte mode, no code restrictions
10
Byte mode, but 0x00 and 0xFF prevented
(0x00 replaced by 0x01, 0xFF replaced by 0xFE)
11
Reserved
相關PDF資料 |
PDF描述 |
|---|---|
| AD9889BBBCZ-80 | TRANSMITTER HDMI/DVI 76-CSPBGA |
| AD8325ARUZ | IC LN DVR CATV FINE-STEP 28TSSOP |
| MAX3430EPA+ | IC TXRX RS-485 3.3V 8-DIP |
| VI-BWM-IV-F3 | CONVERTER MOD DC/DC 10V 150W |
| VI-BW3-IV-F4 | CONVERTER MOD DC/DC 24V 150W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADV7180BST48Z-RL | 功能描述:視頻 IC 48-Lead Low Profile Quad Flat Package RoHS:否 制造商:Fairchild Semiconductor 工作電源電壓:5 V 電源電流:80 mA 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-28 封裝:Reel |
| ADV7180BSTZ | 功能描述:IC VIDEO DECODER SDTV 64-LQFP RoHS:是 類別:集成電路 (IC) >> 線性 - 視頻處理 系列:- 標準包裝:250 系列:- 類型:電平移位器 應用:LCD 電視機/監控器 安裝類型:表面貼裝 封裝/外殼:28-WFQFN 裸露焊盤 供應商設備封裝:28-WQFN（4x4）裸露焊盤 包裝:帶卷 (TR) 其它名稱:296-32523-2TPS65198RUYT-ND |
| ADV7180BSTZ | 制造商:Analog Devices 功能描述:Video IC |
| ADV7180BSTZ-REEL | 功能描述:IC VIDEO DECODER SDTV 64-LQFP RoHS:是 類別:集成電路 (IC) >> 線性 - 視頻處理 系列:- 標準包裝:250 系列:- 類型:電平移位器 應用:LCD 電視機/監控器 安裝類型:表面貼裝 封裝/外殼:28-WFQFN 裸露焊盤 供應商設備封裝:28-WQFN（4x4）裸露焊盤 包裝:帶卷 (TR) 其它名稱:296-32523-2TPS65198RUYT-ND |
| ADV7180KCP32Z | 功能描述:IC VIDEO DECODER 10BIT 32LFCSP RoHS:是 類別:集成電路 (IC) >> 線性 - 視頻處理 系列:- 產品變化通告:Product Discontinuation 07/Mar/2011 標準包裝:3,000 系列:OMNITUNE™ 類型:調諧器 應用:移動電話，手機，視頻顯示器 安裝類型:表面貼裝 封裝/外殼:65-WFBGA 供應商設備封裝:PG-WFSGA-65 包裝:帶卷 (TR) 其它名稱:SP000365064 |
發布緊急采購，3分鐘左右您將得到回復。