ADSP-2183–SPECIFICATIONS
RECOMMENDED OPERATING CONDITIONS
K Grade
Min
B Grade
Min
Parameter
Max
Max
Unit
V
DD
T
AMB
ELECTRICAL CHARACTERISTICS
Supply Voltage
Ambient Operating Temperature
3.0
0
3.6
+70
3.0
–40
3.6
+85
V
°
C
K/B Grades
Min
Parameter
Test Conditions
Typ
Max
Unit
V
IH
V
IL
V
OH
Hi-Level Input Voltage
1, 2
Lo-Level Input Voltage
1, 3
Hi-Level Output Voltage
1, 4, 5
@ V
DD
= max
@ V
DD
= min
@ V
DD
= min
I
OH
= –0.5 mA
@ V
DD
= min
I
OH
= –100
μ
A
6
@ V
DD
= min
I
OL
= 2 mA
@ V
DD
= max
V
IN
= V
DD
max
@ V
DD
= max
V
IN
= 0 V
@ V
DD
= max
V
IN
= V
DD
max
8
@ V
DD
= max
V
IN
= 0 V
8
@ V
DD
= 3.3
T
AMB
= +25
°
C
t
CK
= 19 ns
11
t
CK
= 25 ns
11
t
CK
= 30 ns
11
t
CK
= 34.7 ns
11
@ V
DD
= 3.3
T
AMB
= +25
°
C
t
CK
= 19 ns
11
t
CK
= 25 ns
11
t
CK
= 30 ns
11
t
CK
= 34.7 ns
11
@ V
IN
= 2.5 V
f
IN
= 1.0 MHz
T
AMB
= +25
°
C
@ V
IN
= 2.5 V
f
IN
= 1.0 MHz
T
AMB
= +25
°
C
2.0
V
V
0.4
2.4
V
V
DD
– 0.3
V
V
OL
Lo-Level Output Voltage
1, 4, 5
0.4
V
I
IH
Hi-Level Input Current
3
10
μ
A
I
IL
Lo-Level Input Current
3
10
μ
A
I
OZH
Three-State Leakage Current
7
10
μ
A
I
OZL
Three-State Leakage Current
7
8
μ
A
I
DD
Supply Current (Idle)
9, 10
10
9
8
6
mA
mA
mA
mA
I
DD
Supply Current (Dynamic)
10, 12
44
35
30
26
mA
mA
mA
mA
C
I
Input Pin Capacitance
3, 6, 13
8
pF
C
O
Output Pin Capacitance
6, 7, 13, 14
8
pF
NOTES
Bidirectional pins: D0–D23, RFS0, RFS1, SCLK0, SCLK1, TFS0, TFS1, IAD0–IAD15, PF0–PF7.
1
2
Input only pins:
RESET
,
IRQ2
,
BR
, MMAP, DR0, DR1,
PWD
,
IRQL0
,
IRQL1
,
IRQE
,
IS
,
IRD
,
IWR
, IAL.
1
3
Input only pins: CLKIN,
RESET
,
IRQ2
,
BR
, MMAP, DR0, DR1,
IS
, IAL,
IRD
,
IWR
,
IRQL0
,
IRQL1
,
IRQE
,
PWD
.
1
4
Output pins:
BG
,
PMS
,
DMS
,
BMS
,
IOMS
,
CMS
,
RD
,
WR
,
IACK
, PWDACK, A0–A13, DT0, DT1, CLKOUT, FL2-0.
1
5
Although specified for TTL outputs, all ADSP-2183 outputs are CMOS-compatible and will drive to V
DD
and GND, assuming no dc loads.
1
6
Guaranteed but not tested.
1
7
Three-statable pins: A0–A13, D0–D23,
PMS
,
DMS
,
BMS
,
IOMS
,
CMS
,
RD
,
WR
, DT0, DT1, SCLK0, SCLK1, TFS0, TFS1, RFS0, RFS1, IAD0–IAD15, PF0–PF7.
1
8
0 V on
BR
, CLKIN Active (to force three-state condition).
1
9
Idle refers to ADSP-2183 state of operation during execution of IDLE instruction. Deasserted pins are driven to either V
DD
or GND.
10
Current reflects device operating with no output loads.
11
V
IN
= 0.4 V and 2.4 V. For typical figures for supply currents, refer to Power Dissipation section.
12
I
DD
measurement taken with all instructions executing from internal memory. 50% of the instructions are multifunction (types 1, 4, 5, 12, 13, 14), 30% are
1
type 2 and type 6, and 20% are idle instructions.
13
Applies to LQFP package type and Mini-BGA.
14
Output pin capacitance is the capacitive load for any three-stated output pin.
Specifications subject to change without notice.
–12–
REV. C