參數資料
型號： ADSP21020
廠商： Analog Devices, Inc.
元件分類： 數字信號處理
英文描述： 32/40-Bit IEEE Floating-Point DSP Microprocessor
中文描述： 32/40 IEEE浮點DSP微處理器
文件頁數： 5/32頁
文件大?。?/td> 425K
代理商： ADSP21020
ADSP-21020
REV. C
–5–
4
1
×
CLOCK
CLKIN
PMA
PMD
DMACK
DMA
DMD
ADSP-21010
24
48
32
32
2
PMACK
4
DMPAGE
PMPAGE
F
J
5
4
R
T
ADDR
DATA
PROGRAM
MEMORY
SELECTS
OE
WE
PMS1-0
PMRD
PMWR
DMRD
DMWR
DMTS
DATA
MEMORY
ACK
ADDR
DATA
PERIPHERALS
ADDR
DATA
SELECTS
OE
WE
SELECTS
OE
WE
B
B
RESET
IRQ3-0
PMTS
DMS3-0
Figure 2. Basic System Configuration
The ADSP-21020 also implements on-chip emulation through
the JTAG test access port. The processor’s eight sets of break-
point range registers enable program execution at full speed
until reaching a desired break-point address range. The
processor can then halt and allow reading/writing of all the
processor’s internal registers and external memories through the
JTAG port.
PIN DESCRIPTIONS
This section describes the pins of the ADSP-21020. When
groups of pins are identified with subscripts, e.g. PMD
47–0
, the
highest numbered pin is the MSB (in this case, PMD
47
). Inputs
identified as synchronous (S) must meet timing requirements
with respect to CLKIN (or with respect to TCK for TMS, TDI,
and
TRST
). Those that are asynchronous (A) can be asserted
asynchronously to CLKIN.
O = Output; I = Input; S = Synchronous; A = Asynchronous;
P = Power Supply; G = Ground.
Pin
Name
Type
Function
PMA
23–0
O
Program Memory Address. The ADSP-21020
outputs an address in program memory on
these pins.
Program Memory Data. The ADSP-21020
inputs and outputs data and instructions on
these pins. 32-bit fixed-point data and 32-bit
single-precision floating-point data is trans-
ferred over bits 47-16 of the PMD bus.
Program Memory Select lines. These pins are
asserted as chip selects for the corresponding
banks of program memory. Memory banks
must be defined in the memory control
registers. These pins are decoded program
memory address lines and provide an early
indication of a possible bus cycle.
Program Memory Read strobe. This pin is
asserted when the ADSP-21020 reads from
program memory.
Program Memory Write strobe. This pin is
asserted when the ADSP-21020 writes to
program memory.
Program Memory Acknowledge. An external
device deasserts this input to add wait states
to a memory access.
PMD
47–0
I/O
PMS
1–0
O
PMRD
O
PMWR
O
PMACK I/S
Pin
Name
Type
Function
PMPAGE O
Program Memory Page Boundary. The
ADSP-21020 asserts this pin to signal that a
program memory page boundary has been
crossed. Memory pages must be defined in
the memory control registers.
Program Memory Three-State Control.
PMTS
places the program memory address,
data, selects, and strobes in a high-
impedance state. If
PMTS
is asserted while
a PM access is occurring, the processor will
halt and the memory access will not be
completed. PMACK must be asserted for at
least one cycle when
PMTS
is deasserted to
allow any pending memory access to com-
plete properly.
PMTS
should only be
asserted (low) during an active memory
access cycle.
Data Memory Address. The ADSP-21020
outputs an address in data memory on these
pins.
Data Memory Data. The ADSP-21020
inputs and outputs data on these pins.
32-bit fixed point data and 32-bit
single-precision floating point data is
transferred over bits 39-8 of the DMD bus.
Data Memory Select lines. These pins are
asserted as chip selects for the correspon-
ding banks of data memory. Memory banks
must be defined in the memory control
registers. These pins are decoded data
memory address lines and provide an early
indication of a possible bus cycle.
Data Memory Read strobe. This pin is
asserted when the ADSP-21020 reads from
data memory.
Data Memory Write strobe. This pin is
asserted when the ADSP-21020 writes to
data memory.
Data Memory Acknowledge. An external
device deasserts this input to add wait states
to a memory access.
PMTS
I/S
DMA
31–0
O
DMD
39–0
I/O
DMS
3–0
O
DMRD
O
DMWR
O
DMACK
I/S
相關PDF資料
PDF描述
ADSP-21020BG-100 32/40-Bit IEEE Floating-Point DSP Microprocessor
ADSP2184 16 A SPDT MINIATURE POWER RELAY
ADSP2185 DSP Microcomputer
ADSP2186 DSP Microcomputer
ADT14 Circular Connector; No. of Contacts:61; Series:LJT07R; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:25; Circular Contact Gender:Socket; Circular Shell Style:Jam Nut Receptacle; Insert Arrangement:25-61
相關代理商/技術參數
參數描述
ADSP-21020 制造商:未知廠家 制造商全稱:未知廠家 功能描述:
ADSP-21020BG-100 制造商:AD 制造商全稱:Analog Devices 功能描述:32/40-Bit IEEE Floating-Point DSP Microprocessor
ADSP-21020BG-120 制造商:AD 制造商全稱:Analog Devices 功能描述:32/40-Bit IEEE Floating-Point DSP Microprocessor
ADSP-21020BG-80 制造商:AD 制造商全稱:Analog Devices 功能描述:32/40-Bit IEEE Floating-Point DSP Microprocessor
ADSP-21020KG-100 制造商:AD 制造商全稱:Analog Devices 功能描述:32/40-Bit IEEE Floating-Point DSP Microprocessor
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*