參數資料
型號： ADSP-21XX
廠商： Analog Devices, Inc.
英文描述： ADSP-2100 Family DSP Microcomputers
中文描述： 的ADSP - 2100系列DSP的微機
文件頁數： 8/32頁
文件大?。?/td> 231K
代理商： ADSP-21XX
ADSP-21mod870
–8–
REV. 0
Reset
The
RESET
signal initiates a master reset of the ADSP-
21mod870. The
RESET
signal must be asserted during the
power-up sequence to assure proper initialization.
RESET
during initial power-up must be held long enough to allow the
internal clock to stabilize. If
RESET
is activated any time after
power-up, the clock continues to run and does not require
stabilization time.
The power-up sequence is defined as the total time required for
the crystal oscillator circuit to stabilize after a valid V
DD
is ap-
plied to the processor, and for the internal phase-locked loop
(PLL) to lock onto the specific crystal frequency. A minimum
of 2000 CLKIN cycles ensures that the PLL has locked but
does not include the crystal oscillator start-up time. During
this power-up sequence the
RESET
signal should be held low.
On any subsequent resets, the
RESET
signal must meet the
minimum pulsewidth specification, t
RSP
.
The
RESET
input contains some hysteresis; however, if you use
an RC circuit to generate your
RESET
signal, the use of an
external Schmidt trigger is recommended.
The master reset sets all internal stack pointers to the empty
stack condition, masks all interrupts and clears the MSTAT
register. When
RESET
is released, if there is no pending bus
request and the chip is configured for booting, the boot-loading
sequence is performed. The first instruction is fetched from
on-chip program memory location 0x0000 once boot loading
completes.
Table II. Modes of Operation
1
MODE D
2
MODE C
3
MODE B
4
MODE A
5
Booting Method
X
0
0
0
BDMA feature is used to load the first 32 program memory words from the
byte memory space. Program execution is held off until all 32 words have
been loaded. Chip is configured in Full Memory Mode.
6
X
0
1
0
No automatic boot operations occur. Program execution starts at external
memory location 0. Chip is configured in Full Memory Mode. BDMA can
still be used but the processor does not automatically use or wait for these
operations.
0
1
0
0
BDMA feature is used to load the first 32 program memory words from the
byte memory space. Program execution is held off until all 32 words have
been loaded. Chip is configured in Host Mode.
IACK
has active pull-down.
(REQUIRES ADDITIONAL HARDWARE).
0
1
0
1
IDMA feature is used to load any internal memory as desired. Program ex-
ecution is held off until internal program memory location 0 is written to.
Chip is configured in Host Mode.
6
IACK
has active pull-down.
1
1
0
0
BDMA feature is used to load the first 32 program memory words from the
byte memory space. Program execution is held off until all 32 words have
been loaded. Chip is configured in Host Mode;
IACK
requires external pull-
down.
(REQUIRES ADDITIONAL HARDWARE).
1
1
0
1
IDMA feature is used to load any internal memory as desired. Program ex-
ecution is held off until internal program memory location 0 is written to.
Chip is configured in Host Mode.
IACK
requires external pull-down.
6
NOTES
1
All mode pins are recognized while
RESET
is active (low).
2
When Mode D = 0 and in host mode,
IACK
is an active, driven signal and cannot be “wire ORed.”
When Mode D = 1 and in host mode,
IACK
is an open source and requires an external pull-down, multiple
IACK
pins can be “wire ORed” together.
3
When Mode C = 0, Full Memory Mode enabled. When Mode C = 1, Host Memory Mode enabled.
4
When Mode B = 0, Auto Booting enabled. When Mode B = 1, no Auto Booting.
5
When Mode A = 0, BDMA enabled. When Mode A = 1, IDMA enabled.
6
Considered standard operating settings. Using these configurations allows for easier design and better memory management.
MODES OF OPERATION
Table II summarizes the ADSP-21mod870 memory modes.
Setting Memory Mode
The ADSP-21mod870 uses the Mode C pin to make a Memory
Mode selection during chip reset. This pin is multiplexed with
the processor’s PF2 pin, so exercise care when selecting a mode.
The two methods for selecting the value of Mode C are active
and passive.
Passive configuration
uses a pull-up or pull-down resistor
connected to the Mode C pin. To minimize power consump-
tion, or if the PF2 pin is used as an output in the DSP applica-
tion, use a weak pull-up or pull-down, on the order of 100 k
.
This value should be sufficient to pull the pin to the desired
level and still let the pin operate as a programmable flag output
without undue strain on the processor’s output driver. For mini-
mum power consumption during power-down, reconfigure PF2
as an input, as the pull-up or pull-down will hold the pin in a
known state, and will not switch.
Active configuration
uses a three-statable external driver con-
nected to the Mode C pin. A driver’s output enable should be
connected to the processor’s
RESET
signal so it only drives the
PF2 pin when
RESET
is active (low). When
RESET
is de-as-
serted, the driver should three-state, allowing the PF2 pin to be
an input or output. To minimize power consumption during
power-down, configure the programmable flag as an output when
connected to a three-stated buffer. This ensures that the pin is
相關PDF資料
PDF描述
ADSP-21MOD970-110 Multiport Internet Gateway Processor Solution
ADSP-21mod970-110 Data Pump Solution Gateway Processor Solution(多端口網關處理器解決方案)
ADSP-21MOD980N MultiPort Internet Gateway Processor
ADSP-21MOD980N-000 CAP 27PF 100V 10% X7R AXIAL BULK M-MIL-PRF-39014
ADSP-21MSP58BST-104 DSP Microcomputers
相關代理商/技術參數
參數描述
ADSP-3128AJG 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:Analog Devices 功能描述:
ADSP-3128ASG/883B 制造商:Rochester Electronics LLC 功能描述:- Bulk
ADSP-3201JG 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:Analog Devices 功能描述:
ADSP-3201KG 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:Analog Devices 功能描述:MULTIPLIER, 144 Pin, Ceramic, PGA
ADSP-3201TG 制造商:Rochester Electronics LLC 功能描述:- Bulk
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*