- 您現在的位置：買賣IC網 > PDF目錄1900 > ADSP-2186BSTZ-160 (Analog Devices Inc)IC DSP CONTROLLER 16BIT 100LQFP PDF資料下載
參數資料
| 型號： | ADSP-2186BSTZ-160 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 3/36頁 |
| 文件大小： | 0K |
| 描述： | IC DSP CONTROLLER 16BIT 100LQFP |
| 標準包裝： | 1 |
| 系列： | ADSP-21xx |
| 類型： | 定點 |
| 接口： | 主機接口，串行端口 |
| 時鐘速率： | 40MHz |
| 非易失內存： | 外部 |
| 芯片上RAM： | 40kB |
| 電壓 - 輸入/輸出： | 5.00V |
| 電壓 - 核心： | 5.00V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 100-LQFP |
| 供應商設備封裝： | 100-LQFP（14x14） |
| 包裝： | 托盤 |
第1頁第2頁當前第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
ADSP-2186
–11–
REV. B
Table VI. Boot Summary Table
Mode C
Mode B
Mode A
Booting Method
0
BDMA feature is used to load
the first 32 program memory
words from the byte memory
space. Program execution is
held off until all 32 words have
been loaded. Chip is config-
ured in Full Memory Mode.
0
1
0
No Automatic boot operations
occur. Program execution
starts at external memory
location 0. Chip is configured
in Full Memory Mode.
BDMA can still be used but
the processor does not auto-
matically use or wait for these
operations.
1
0
BDMA feature is used to load
the first 32 program memory
words from the byte memory
space. Program execution is
held off until all 32 words have
been loaded. Chip is config-
ured in Host Mode. Additional
interface hardware is required.
1
0
1
IDMA feature is used to load
any internal memory as de-
sired. Program execution is
held off until internal program
memory location 0 is written
to. Chip is configured in Host
Mode.
The BDMA interface is set up during reset to the following
defaults when BDMA booting is specified: the BDIR, BMPAGE,
BIAD and BEAD registers are set to 0; the BTYPE register is
set to 0 to specify program memory 24-bit words; and the
BWCOUNT register is set to 32. This causes 32 words of on-chip
program memory to be loaded from byte memory. These 32
words are used to set up the BDMA to load in the remaining
program code. The BCR bit is also set to 1, which causes pro-
gram execution to be held off until all 32 words are loaded into
on-chip program memory. Execution then begins at address 0.
The ADSP-2100 Family development software (Revision 5.02
and later) fully supports the BDMA booting feature and can
generate byte memory space compatible boot code.
The IDLE instruction can also be used to allow the processor
to hold off execution while booting continues through the
BDMA interface. For BDMA accesses while in Host Mode, the
addresses to boot memory must be constructed externally to
the ADSP-2186. The only memory address bit provided by
the processor is A0.
IDMA Port Booting
The ADSP-2186 can also boot programs through its Internal
DMA port. If Mode C = 1, Mode B = 0, and Mode A = 1, the
ADSP-2186 boots from the IDMA port. The IDMA feature can
load as much on-chip memory as desired. Program execution is
held off until on-chip program memory location 0 is written to.
Bus Request and Bus Grant
The ADSP-2186 can relinquish control of the data and address
buses to an external device. When the external device requires
access to memory, it asserts the bus request (
BR) signal. If the
ADSP-2186 is not performing an external memory access, it
responds to the active BR input in the following processor cycle by:
Three-stating the data and address buses and the
PMS, DMS,
BMS, CMS, IOMS, RD, WR output drivers,
Asserting the bus grant (
BG) signal, and
Halting program execution.
If Go Mode is enabled, the ADSP-2186 will not halt program
execution until it encounters an instruction that requires an
external memory access.
If the ADSP-2186 is performing an external memory access
when the external device asserts the
BR signal, it will not three-
state the memory interfaces or assert the
BG signal until the
processor cycle after the access completes. The instruction does
not need to be completed when the bus is granted. If a single
instruction requires two external memory accesses, the bus will
be granted between the two accesses.
When the
BR signal is released, the processor releases the BG
signal, reenables the output drivers and continues program
execution from the point at which it stopped.
The bus request feature operates at all times, including when
the processor is booting and when
RESET is active.
The
BGH pin is asserted when the ADSP-2186 is ready to
execute an instruction but is stopped because the external bus is
already granted to another device. The other device can release
the bus by deasserting bus request. Once the bus is released, the
ADSP-2186 deasserts
BG and BGH and executes the external
memory access.
Flag I/O Pins
The ADSP-2186 has eight general purpose programmable input/
output flag pins. They are controlled by two memory mapped
registers. The PFTYPE register determines the direction,
1 = output and 0 = input. The PFDATA register is used to read
and write the values on the pins. Data being read from a pin
configured as an input is synchronized to the ADSP-2186’s
clock. Bits that are programmed as outputs will read the value
being output. The PF pins default to input during reset.
In addition to the programmable flags, the ADSP-2186 has five
fixed-mode flags, FI, FO, FL0, FL1 and FL2. FL0–FL2 are
dedicated output flags. FI and FO are available as an alter-
nate configuration of SPORT1.
Note: Pins PF0, PF1 and PF2 are also used for device configu-
ration during reset.
相關PDF資料 |
PDF描述 |
|---|---|
| ADSP-2186MKCA-300 | IC DSP CONTROLLER 16BIT 144MBGA |
| ADSP-2187LBSTZ-210 | IC DSP CONTROLLER 16BIT 100-TQFP |
| ADSP-2188MKSTZ-300 | IC DSP CONTROLLER 16BIT 100LQFP |
| ADSP-2189MKCA-300 | IC DSP CONTROLLER 16BIT 144MBGA |
| ADSP-2189NBCA-320 | IC DSP 16BIT 80MHZ 144CSPBGA |
相關代理商/技術參數 |
參數描述 |
|---|---|
| adsp-2186kst-1 | 制造商:Analog Devices 功能描述: |
| ADSP-2186KST-115 | 制造商:Analog Devices 功能描述:DSP Fixed-Point 16-Bit 28.8MHz 28.8MIPS 100-Pin LQFP 制造商:Rochester Electronics LLC 功能描述:DSP,5V,33MHZ,16K WORD RAM, 100TQFP - Bulk 制造商:Analog Devices 功能描述:DSP microcomputer 28.8 MHz speed 1 tim |
| ADSP-2186KST-133 | 制造商:Analog Devices 功能描述:DSP Fixed-Point 16-Bit 33.3MHz 33.3MIPS 100-Pin LQFP 制造商:Rochester Electronics LLC 功能描述:DSP FIX PT 16BIT 33.3MHZ 33.3MIPS 100LQFP - Bulk 制造商:Analog Devices 功能描述:IC MICROCOMPUTER 16-BIT |
| ADSP-2186KST-160 | 制造商:Analog Devices 功能描述:DSP Fixed-Point 16-Bit 40MHz 40MIPS 100-Pin LQFP 制造商:Rochester Electronics LLC 功能描述:5V 16BIT DSP,40MIPS,8KWORDSPM/DM,100TQFP - Bulk 制造商:Analog Devices 功能描述:IC MICROCOMPUTER 16-BIT |
| ADSP-2186KST-1606 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
發布緊急采購，3分鐘左右您將得到回復。