- 您現在的位置：買賣IC網 > PDF目錄374035 > ADSP-2184 (Analog Devices, Inc.) LM2941/LM2941C 1A Low Dropout Adjustable Regulator; Package: TO-263; No of Pins: 5; Qty per Container: 45; Container: Rail PDF資料下載
參數資料
| 型號： | ADSP-2184 |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | LM2941/LM2941C 1A Low Dropout Adjustable Regulator; Package: TO-263; No of Pins: 5; Qty per Container: 45; Container: Rail |
| 中文描述： | DSP的微機 |
| 文件頁數： | 12/31頁 |
| 文件大?。?/td> | 216K |
| 代理商： | ADSP-2184 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁當前第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁
ADSP-2184L
–12–
REV. 0
Target Board Connector for EZ-ICE Probe
The EZ-ICE connector (a standard pin strip header) is shown in
Figure 8. You must add this connector to your target board
design if you intend to use the EZ-ICE. Be sure to allow
enough room in your system to fit the EZ-ICE probe onto the
14-pin connector.
7
1
2
3
4
5
6
8
9
10
11
12
13
14
GND
RESET
BR
BG
TOP VIEW
EBG
EBR
ELOUT
EE
EINT
ELIN
ECLK
EMS
ERESET
KEY (NO PIN)
Figure 8. Target Board Connector for EZ-ICE
The 14-pin, 2-row pin strip header is keyed at the Pin 7 loca-
tion—you must remove Pin 7 from the header. The pins must
be 0.025 inch square and at least 0.20 inch in length. Pin spac-
ing should be 0.1
×
0.1 inches. The pin strip header must have
at least 0.15-inch clearance on all sides to accept the EZ-ICE
probe plug. Pin strip headers are available from vendors such as
3M, McKenzie and Samtec.
Target Memory Interface
For your target system to be compatible with the EZ-ICE
emu-
lator, it must comply with the memory interface guidelines listed
below.
PM, DM, BM, IOM, and CM
Design Program Memory (PM), Data Memory (DM), Byte
Memory (BM), I/O Memory (IOM) and Composite Memory
(CM) external interfaces to comply with worst case device tim-
ing requirements and switching characteristics as specified in
this DSP’s data sheet. The performance of the EZ-ICE may ap-
proach published worst case specification for some memory
access timing requirements and switching characteristics.
Note: If your target does not meet the worst case chip specifica-
tions for memory access parameters, you may not be able to
emulate your circuitry at the desired CLKIN frequency. Depend-
ing on the severity of the specification violation, you may have
trouble manufacturing your system as DSP components statisti-
cally vary in switching characteristics and timing requirements
within published limits.
Restriction: All memory strobe signals on the ADSP-2184L
(
RD
,
WR
,
PMS
,
DMS
,
BMS
,
CMS
and
IOMS
) used in your
target system must have 10 k
pull-up resistors connected when
the EZ-ICE is being used. The pull-up resistors are necessary
because there are no internal pull-ups to guarantee their state
during prolonged three-state conditions resulting from typical
EZ-ICE
debugging sessions. These resistors may be removed at
your option when the EZ-ICE
is not being used.
Target System Interface Signals
When the EZ-ICE
board is installed, the performance of some
system signals change. Design your system to be compatible
with the following system interface signal changes introduced by
the EZ-ICE
board:
EZ-ICE
emulation introduces an 8 ns propagation delay be-
tween your target circuitry and the DSP on the
RESET
signal.
EZ-ICE
emulation introduces an 8 ns propagation delay be-
tween your target circuitry and the DSP on the
BR
signal.
EZ-ICE
emulation ignores
RESET
and
BR
when single-
stepping.
EZ-ICE
emulation ignores
RESET
and
BR
when in Emulator
Space (DSP halted).
EZ-ICE
emulation ignores the state of target
BR
in certain
modes. As a result, the target system may take control of the
DSP’s external memory bus only if bus grant (
BG
) is asserted
by the EZ-ICE
board’s DSP.
相關PDF資料 |
PDF描述 |
|---|---|
| ADSP-2184BST-160 | DSP Microcomputer |
| ADSP-2184L | LM2941/LM2941C 1A Low Dropout Adjustable Regulator; Package: TO-220; No of Pins: 5; Qty per Container: 45; Container: Rail |
| ADSP-2184NKST-320 | DSP Microcomputer |
| ADSP-2186NKCA-320 | DSP Microcomputer |
| ADSP-2184N | DSP Microcomputer |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADSP-2184BST-160 | 制造商:Analog Devices 功能描述:DSP Fixed-Point 16-Bit 40MHz 40MIPS 100-Pin LQFP 制造商:Analog Devices 功能描述:IC MICROCOMPUTER 16-BIT |
| ADSP-2184BSTZ-160 | 功能描述:IC DSP CONTROLLER 16BIT 100LQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:ADSP-21xx 標準包裝:40 系列:TMS320DM64x, DaVinci™ 類型:定點 接口:I²C，McASP，McBSP 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:160kB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:0°C ~ 90°C 安裝類型:表面貼裝 封裝/外殼:548-BBGA，F(xiàn)CBGA 供應商設備封裝:548-FCBGA（27x27） 包裝:托盤 配用:TMDSDMK642-0E-ND - DEVELPER KIT W/NTSC CAMERA296-23038-ND - DSP STARTER KIT FOR TMS320C6416296-23059-ND - FLASHBURN PORTING KIT296-23058-ND - EVAL MODULE FOR DM642TMDSDMK642-ND - DEVELOPER KIT W/NTSC CAMERA |
| ADSP-2184BSTZ-160 | 制造商:Analog Devices 功能描述:Digital Signal Processor IC |
| ADSP-2184L | 制造商:AD 制造商全稱:Analog Devices 功能描述:DSP Microcomputer |
| ADSP-2184LBST-160 | 制造商:Analog Devices 功能描述:DSP Fixed-Point 16-Bit 40MHz 40MIPS 100-Pin LQFP 制造商:Analog Devices 功能描述:IC MICROCOMPUTER 16-BIT |
發布緊急采購，3分鐘左右您將得到回復。