- 您現在的位置：買賣IC網 > PDF目錄375263 > ADS1252K5 (Texas Instruments, Inc.) 24-Bit, 20kHz, Low-Power ANALOG-TO-DIGITAL CONVERTER PDF資料下載
參數資料
| 型號： | ADS1252K5 |
| 廠商： | Texas Instruments, Inc. |
| 英文描述： | 24-Bit, 20kHz, Low-Power ANALOG-TO-DIGITAL CONVERTER |
| 中文描述： | 24位20kHz的，低功耗模擬數字轉換器 |
| 文件頁數： | 13/14頁 |
| 文件大小： | 131K |
| 代理商： | ADS1252K5 |
13
ADS1252
LAYOUT
POWER SUPPLY
The power supply should be well regulated and low noise.
For designs requiring very high resolution from the ADS1252,
power supply rejection will be a concern. Avoid running
digital lines under the device as they may couple noise onto
the die. High frequency noise can capacitively couple into
the analog portion of the device and will alias back into the
passband of the digital filter, affecting the conversion result.
GROUNDING
The analog and digital sections of the system design should
be carefully and cleanly partitioned. Each section should
have its own ground plane with no overlap between them.
GND should be connected to the analog ground plane, as
well as all other analog grounds. Do not join the analog and
digital ground planes on the board, but instead connect the
two with a moderate signal trace. For multiple converters,
connect the two ground planes at one location as central to
all of the converters as possible. In some cases, experimen-
tation may be required to find the best point to connect the
two planes together. The printed circuit board can be de-
signed to provide different analog/digital ground connec-
tions via short jumpers. The initial prototype can be used to
establish which connection works best.
DECOUPLING
Good decoupling practices should be used for the ADS1252
and for all components in the design. All decoupling capaci-
tors, and specifically the 0.1
μ
F ceramic capacitors, should
be placed as close as possible to the pin being decoupled. A
1
μ
F to 10
μ
F capacitor, in parallel with a 0.1
μ
F ceramic
capacitor, should be used to decouple V
D
to GND.
SYSTEM CONSIDERATIONS
The recommendations for power supplies and grounding will
change depending on the requirements and specific design of
the overall system. Achieving 24 bits of noise performance
is a great deal more difficult than achieving 12 bits of noise
performance. In general, a system can be broken up into four
different stages:
Analog Processing
Analog Portion of the ADS1252
Digital Portion of the ADS1252
Digital Processing
For the simplest system consisting of minimal analog signal
processing (basic filtering and gain), a microcontroller, and
one clock source, one can achieve high resolution by power-
ing all components by a common power supply. In addition,
all components could share a common ground plane. Thus,
there would be no distinctions between “analog” power and
ground, and “digital” power and ground. The layout should
still include a power plane, a ground plane, and careful
decoupling. In a more extreme case the design could include:
Multiple ADS1252s
Extensive Analog Signal Processing
One or More Microcontrollers, Digital Signal Processors,
or Microprocessors
Many Different Clock Sources
Interconnections to Various Other Systems
High resolution will be very difficult to achieve for this
design. The approach would be to break the system into as
many different parts as possible. For example, each ADS1252
may have its own “analog” processing front end.
FIGURE 16. Isolated Three-Wire Interface.
ISO150
D
1
R
1
V
S
G
B
R
1
D
1
D
2
R
2
G
A
V
S
R
2
D
2
V
DD2
V
DD1
V
DD1
V
DD2
GND
GND
GND
GND
DOUT/DRDY
SCLK
+V
IN
–V
IN
+V
DD
CLK
V
REF
GND
SCLK
DOUT/DRDY
V
Circuit
ADS1252
V
S
相關PDF資料 |
PDF描述 |
|---|---|
| ADS1254 | 24-Bit, 20kHz, Low Power ANALOG-TO-DIGITAL CONVERTER |
| ADS1254E | 24-Bit, 20kHz, Low Power ANALOG-TO-DIGITAL CONVERTER |
| ADS1255IDB | Very Low Noise, 24-Bit Analog-to-Digital Converter |
| ADS1255IDBR | Very Low Noise, 24-Bit Analog-to-Digital Converter |
| ADS1255IDBT | Very Low Noise, 24-Bit Analog-to-Digital Converter |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADS1252U | 功能描述:模數轉換器 - ADC ResolutionPlus 24-Bit 40kHz RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| ADS1252U | 制造商:Texas Instruments 功能描述:IC 24BIT ADC 41.7KSPS SMD |
| ADS1252U/2K5 | 功能描述:模數轉換器 - ADC ResolutionPlus 24-Bit 40kHz RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| ADS1252U/2K5G4 | 功能描述:模數轉換器 - ADC ResolutionPlus 24-Bit 40kHz RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| ADS1252UG4 | 功能描述:模數轉換器 - ADC ResolutionPlus 24-Bit 40kHz RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
發布緊急采購，3分鐘左右您將得到回復。