- 您現在的位置：買賣IC網 > PDF目錄1989 > ADN2811ACPZ-CML (Analog Devices Inc)IC CLK/DATA REC W/AMP 48-LFCSP PDF資料下載
參數資料
| 型號： | ADN2811ACPZ-CML |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 7/20頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC CLK/DATA REC W/AMP 48-LFCSP |
| 標準包裝： | 1 |
| 類型： | 時鐘和數據恢復（CDR），多路復用器 |
| PLL： | 是 |
| 主要目的： | SONET/SDH，STM |
| 輸入： | CML |
| 輸出： | CML |
| 電路數： | 1 |
| 比率 - 輸入:輸出： | 1:2 |
| 差分 - 輸入:輸出： | 是/是 |
| 頻率 - 最大： | 2.66GHz |
| 電源電壓： | 3 V ~ 3.6 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 48-VFQFN 裸露焊盤，CSP |
| 供應商設備封裝： | 48-LFCSP |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁
ADN2811
Rev. B | Page 15 of 20
APPLICATIONS INFORMATION
PCB DESIGN GUIDELINES
Proper RF PCB design techniques must be used for optimal
performance.
Power Supply Connections and Ground Planes
Use of one low impedance ground plane to both analog and
digital grounds is recommended. The VEE pins should be
soldered directly to the ground plane to reduce series
inductance. If the ground plane is an internal plane and
connections to the ground plane are made through vias,
multiple vias may be used in parallel to reduce the series
inductance, especially on Pins 33 and 34, which are the ground
returns for the output buffers.
Use of a 10 F electrolytic capacitor between VCC and GND is
recommended at the location where the 3.3 V supply enters the
PCB. 0.1 F and 1 nF ceramic chip capacitors should be placed
between IC power supply VCC and GND as close as possible to
the ADN2811’s VCC pins. Again, if connections to the supply
and ground are made through vias, the use of multiple vias in
parallel helps to reduce series inductance, especially on Pins 35
and 36, which supply power to the high speed CLKOUTP/N
and DATAOUTP/N output buffers. Refer to the schematic in
Figure 19 for recommended connections.
Transmission Lines
Use of 50 transmission lines is required for all high frequency
input and output signals to minimize reflections, including PIN,
NIN, CLKOUTP, CLKOUTN, DATAOUTP, and DATAOUTN
(also REFCLKP, REFCLKN for a 155.2 MHz REFCLK). It is also
recommended that the PIN/NIN input traces are matched in
length and that the CLKOUTP/N and DATAOUTP/N output
traces are matched in length. All high speed CML outputs,
CLKOUTP/N and DATAOUTP/N, also require 100 back
termination chip resistors connected between the output pin
and VCC. These resistors should be placed as close as possible
to the output pins. These 100 resistors are in parallel with
on-chip 100 termination resistors to create a 50 back
termination (see Figure 20).
The high speed inputs, PIN and NIN, are internally terminated
with 50 to an internal reference voltage (see Figure 21). A
0.1 F capacitor is recommended between VREF, Pin 4, and
GND to provide an ac ground for the inputs.
As with any high speed mixed-signal design, care should be
taken to keep all high speed digital traces away from sensitive
analog nodes.
Soldering Guidelines for Chip-Scale Package
The lands on the 48-lead LFCSP are rectangular. The printed
circuit board pad for these should be 0.1 mm longer than the
package land length and 0.05 mm wider than the package land
width. The land should be centered on the pad. This ensures
that the solder joint size is maximized. The bottom of the chip
scale package has a central exposed pad. The pad on the printed
circuit board should be at least as large as this exposed pad. The
user must connect the exposed pad to analog VCC.
If vias are used, they should be incorporated into the pad at
1.2 mm pitch grid. The via diameter should be between 0.3 mm
and 0.33 mm, and the via barrel should be plated with 1 oz.
copper to plug the via.
相關PDF資料 |
PDF描述 |
|---|---|
| ADN2812ACPZ-RL7 | IC CLOCK/DATA RECOVERY 32LFCSP |
| ADN2813ACPZ-500RL7 | IC CLK/DATA REC 1.25GBPS 32LFCSP |
| ADN2814ACPZ-500RL7 | IC CLK/DATA REC 675MBPS 32-LFCSP |
| ADN2815ACPZ | IC CLK/DATA REC 1.25GBPS 32LFCSP |
| ADN2816ACPZ-500RL7 | IC CLK/DATA REC 675MBPS 32-LFCSP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADN2811ACPZ-CML-RL | 功能描述:IC CLK DATA REC SDH 2.66GHZ 制造商:analog devices inc. 系列:- 包裝:帶卷（TR） 零件狀態:上次購買時間 PLL:是 主要用途:SONET/SDH，STM 輸入:CML 輸出:CML 電路數:1 比率 - 輸入:輸出:1:2 差分 - 輸入:輸出:是/是 頻率 - 最大值:2.66GHz 電壓 - 電源:3 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-WFQFN 裸露焊盤 供應商器件封裝:48-LFCSP（7x7） 標準包裝:1 |
| ADN2812 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Continuous Rate 12.3 Mb/s to 2.7 Gb/s Clock and Data Recovery IC with Integrated Limiting Amp |
| ADN2812ACP | 制造商:Analog Devices 功能描述:IC CLOCK/DATA RECOVERY |
| ADN2812ACP-RL | 制造商:Analog Devices 功能描述:Clock and Data Recovery 32-Pin LFCSP EP T/R |
| ADN2812ACP-RL7 | 制造商:Analog Devices 功能描述:Clock and Data Recovery 32-Pin LFCSP EP T/R |
發布緊急采購，3分鐘左右您將得到回復。