- 您現在的位置：買賣IC網 > PDF目錄11749 > ADM1024ARUZ-REEL (ON Semiconductor)IC MONITOR SYS TEMP/VOLT 24TSSOP PDF資料下載
參數資料
| 型號： | ADM1024ARUZ-REEL |
| 廠商： | ON Semiconductor |
| 文件頁數： | 29/30頁 |
| 文件大小： | 0K |
| 描述： | IC MONITOR SYS TEMP/VOLT 24TSSOP |
| 產品變化通告： | MFG CHG Notification ADI to ON Semi |
| 標準包裝： | 2,500 |
| 應用： | PC，PDA |
| 接口： | 串行 |
| 電源電壓： | 2.8 V ~ 5.5 V |
| 封裝/外殼： | 24-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 24-TSSOP |
| 包裝： | 帶卷 (TR) |
| 安裝類型： | 表面貼裝 |
| 其它名稱： | ADM1024ARUZ-REEL-ND ADM1024ARUZ-REELOSTR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁當前第29頁第30頁
ADM1024
http://onsemi.com
8
General Description
The ADM1024 is a complete system hardware monitor for
microprocessor-based systems. The device communicates
with the system via a serial SMBus. The serial bus controller
has a hardwired address line for device selection (Pin 1), a
serial data line for reading and writing addresses and data
(SDA, Pin 14), and an input line for the serial clock (Pin 3),
and an input line for the serial clock (Pin 4). All control and
programming functions of the ADM1024 are performed over
the serial bus.
Measurement Inputs
Programmability of the measurement inputs makes the
ADM1024 extremely flexible and versatile. The device has
a 10bit ADC and nine measurement input pins that can be
configured in different ways.
Pins 5 and 6 can be programmed as general-purpose
analog inputs with a range of 0 V to 2.5 V, or as digital inputs
to monitor the speed of fans with digital tachometer outputs.
The fan inputs can be programmed to accommodate fans
with different speeds and different numbers of pulses per
revolution from their tachometer outputs.
Pins 13 and 14 are dedicated temperature inputs and may
be connected to the cathode and anode of an external
temperature sensing diode.
Pins 15, 16, and 19 are dedicated analog inputs with
on-chip attenuators, configured to monitor 12 V, 5.0 V, and
the processor core voltage, respectively.
Pins 17 and 18 may be configured as analog inputs with
on-chip attenuators to monitor a second processor core voltage
and a 2.5 V supply, or they may be configured as a temperature
input and connected to a second temperature-sensing diode.
The ADC also accepts input from an on-chip band gap
temperature sensor that monitors system-ambient temperature.
Finally, the ADM1024 monitors the supply from which it
is powered, so there is no need for a separate 3.3 V analog
input if the chip VCC is 3.3 V. The range of this VCC
measurement can be configured for either a 3.3 V or 5.0 V
VCC by Bit 3 of the Channel Mode Register.
Sequential Measurement
When the ADM1024 monitoring sequence is started, it
cycles sequentially through the measurement of analog
inputs and the temperature sensor, while at the same time the
fan speed inputs are independently monitored. Measured
values from these inputs are stored in Value Registers. These
can be read out over the serial bus, or can be compared with
programmed limits stored in the Limit Registers. The results
of out-of-limit comparisons are stored in the Interrupt Status
Registers, and will generate an interrupt on the INT line
(Pin 10).
Any or all of the Interrupt Status Bits can be masked by
appropriate programming of the Interrupt Mask Register.
Processor Voltage ID
Five digital inputs (VID4 to VID0Pins 20 to 24) read the
processor voltage ID code. These inputs can also be
reconfigured as interrupt inputs.
The VID pins have internal 100 k
W pullup resistors.
Chassis Intrusion
A chassis intrusion input (Pin 7) is provided to detect
unauthorized tampering with the equipment.
RESET
A RESET input/output (Pin 12) is provided. Pulling this
pin low will reset all ADM1024 internal registers to default
values. The ADM1024 can also be programmed to give a
low going 45 ms reset pulse at this pin.
Analog Output
The ADM1024 contains an on-chip, 8-bit DAC with an
output range of 0 V to 2.5 V (Pin 11). This is typically used
to implement a temperature-controlled fan by controlling
the speed of a fan dependent upon the temperature measured
by the on-chip temperature sensor.
Testing of board level connectivity is simplified by
providing a NAND tree test function. The AOUT (Pin 11)
also doubles as a NAND test input, while Pin 1 doubles as
a NAND tree output.
Internal Registers of the ADM1024
A brief description of the ADM1024’s principal internal
registers follows. More detailed information on the function
Configuration Registers: Provide control and
configuration.
Channel Mode Register: Stores the data for the
operating modes of the input channels.
Address Pointer Register: This register contains the
address that selects one of the other internal registers.
When writing to the ADM1024, the first byte of data is
always a register address, which is written to the
Address Pointer Register.
Interrupt (INT) Status Registers: Two registers to
provide status of each interrupt event. These registers
are also mirrored at addresses 4Ch and 4Dh.
Interrupt (INT) Mask Registers: Allow masking of
individual interrupt sources.
Temperature Configuration Register: The configuration
of the temperature interrupt is controlled by the lower
three bits of this register.
VID/Fan Divisor Register: The status of the VID0 to
VID4 pins of the processor can be written to and read
from these registers. Divisor values for fan speed
measurement are also stored in this register.
相關PDF資料 |
PDF描述 |
|---|---|
| PIC18LF46K80-I/P | MCU PIC ECAN 64KB FLASH 40DIP |
| MS27468E13B22S | CONN RCPT 22POS JAM NUT W/SCKT |
| VE-B4F-IW-F1 | CONVERTER MOD DC/DC 72V 100W |
| PIC16LC620-04/SO | IC MCU OTP 512X14 COMP 18SOIC |
| VE-B4D-IX-F4 | CONVERTER MOD DC/DC 85V 75W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADM1024ARUZ-REEL7 | 功能描述:IC MONITOR SYS TEMP/VOLT 24TSSOP RoHS:是 類別:集成電路 (IC) >> 接口 - 專用 系列:- 標準包裝:3,000 系列:- 應用:PDA，便攜式音頻/視頻，智能電話 接口:I²C，2 線串口 電源電壓:1.65 V ~ 3.6 V 封裝/外殼:24-WQFN 裸露焊盤 供應商設備封裝:24-QFN 裸露焊盤（4x4） 包裝:帶卷 (TR) 安裝類型:表面貼裝 產品目錄頁面:1015 (CN2011-ZH PDF) 其它名稱:296-25223-2 |
| ADM1024EVB | 功能描述:BOARD EVAL FOR ADM1024 RoHS:否 類別:編程器，開發系統 >> 過時/停產零件編號 系列:- 標準包裝:1 系列:- 傳感器類型:CMOS 成像，彩色（RGB） 傳感范圍:WVGA 接口:I²C 靈敏度:60 fps 電源電壓:5.7 V ~ 6.3 V 嵌入式:否 已供物品:成像器板 已用 IC / 零件:KAC-00401 相關產品:4H2099-ND - SENSOR IMAGE WVGA COLOR 48-PQFP4H2094-ND - SENSOR IMAGE WVGA MONO 48-PQFP |
| ADM1025 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Low-Cost PC Hardware Monitor ASIC |
| ADM1025A | 制造商:AD 制造商全稱:Analog Devices 功能描述:Low-Cost PC Hardware Monitor ASIC |
| ADM1025AARQ | 功能描述:IC MONITOR SYS/VOLT 5CH 16QSOP RoHS:否 類別:集成電路 (IC) >> 接口 - 專用 系列:- 標準包裝:3,000 系列:- 應用:PDA，便攜式音頻/視頻，智能電話 接口:I²C，2 線串口 電源電壓:1.65 V ~ 3.6 V 封裝/外殼:24-WQFN 裸露焊盤 供應商設備封裝:24-QFN 裸露焊盤（4x4） 包裝:帶卷 (TR) 安裝類型:表面貼裝 產品目錄頁面:1015 (CN2011-ZH PDF) 其它名稱:296-25223-2 |
發布緊急采購，3分鐘左右您將得到回復。