參數資料
型號： ADM1024ARUZ-REEL
廠商： ON Semiconductor
文件頁數： 20/30頁
文件大?。?/td> 0K
描述： IC MONITOR SYS TEMP/VOLT 24TSSOP
產品變化通告： MFG CHG Notification ADI to ON Semi
標準包裝： 2,500
應用： PC，PDA
接口： 串行
電源電壓： 2.8 V ~ 5.5 V
封裝/外殼： 24-TSSOP（0.173"，4.40mm 寬）
供應商設備封裝： 24-TSSOP
包裝： 帶卷 (TR)
安裝類型： 表面貼裝
其它名稱： ADM1024ARUZ-REEL-ND
ADM1024ARUZ-REELOSTR
ADM1024
http://onsemi.com
27
Table 13. REGISTER 40H, CONFIGURATION REGISTER 1 (POWER-ON DEFAULT, 08H)
Bit
Name
R/W
Description
0
START
R/W
Logic 1 enables startup of ADM1024; Logic 0 places it in standby mode. Caution:
The outputs of the interrupt pins will not be cleared if the user writes a 0 to this
location after an interrupt has occurred (see “INT Clear” bit). At startup, limit
checking functions and scanning begins. Note, all high and low limits should be set
into the ADM1024 prior to turning on this bit (PowerOn Default = 0).
1
INT_Enable
R/W
Logic 1 enables the INT_output. 1 = Enabled 0 = Disabled (PowerOn Default = 0).
2
THERM
Enable
R/W
0 = THERM disabled
1 = THERM enabled
3
INT_Clear
R/W
During Interrupt Service Routine (ISR), this bit is asserted Logic 1 to clear INT output
without affecting the contents of the Interrupt Status Register. The device will stop
monitoring. It will resume upon clearing of this bit. (PowerOn Default = 0)
4
RESET
R/W
Setting this bit generates a low going 45 ms reset pulse at Pin 12. This bit is
selfclearing and poweron default is 0.
5
Reserved
R/W
Default = 0
6
THERM CLR
R/W
A 1 clears the THERM output without changing the Status Register contents.
7
Initialization
R/W
Logic 1 restores poweron default values to the Configuration Register, Interrupt
Status Registers, Interrupt Mask Registers, Fan Divisor Register, and the
Temperature Configuration Register. This bit automatically clears itself since the
poweron default is 0.
Table 14. REGISTER 41H, INTERRUPT STATUS REGISTER 1 (POWER-ON DEFAULT, 00H)
Bit
Name
R/W
Description
0
2.5 V/External Temp2
Error
Read only
A 1 indicates that a High or Low limit has been exceeded.
1
VCCP1 Error
Read only
A 1 indicates that a High or Low limit has been exceeded.
2
VCC Error
Read only
A 1 indicates that a High or Low limit has been exceeded.
3
5.0 V Error
Read only
A 1 indicates that a High or Low limit has been exceeded.
4
Internal Temp Error
Read only
A 1 indicates that a temperature interrupt has been set, or that a High or Low limit
has been exceeded.
5
External Temp1 Error
Read only
A 1 indicates that a temperature interrupt has been set, or that a High or Low limit
has been exceeded.
6
FAN1/AIN1 Error
Read only
A 1 indicates that a High or Low limit has been exceeded.
7
FAN2/AIN2 Error
Read only
A 1 indicates that a High or Low limit has been exceeded.
Table 15. REGISTER 42H, INTERRUPT STATUS REGISTER 2 (POWER-ON DEFAULT, 00H) (Note 1 and 2)
Bit
Name
R/W
Description
0
12 V Error
Read only
A 1 indicates a High or Low limit has been exceeded.
1
VCCP2 Error
Read only
A 1 indicates a High or Low limit has been exceeded.
2
Reserved
Read only
Undefined.
3
Reserved
Read only
Undefined.
4
Chassis Error
Read only
A 1 indicates Chassis Intrusion has gone high.
5
THERM Interrupt
Read only
Indicates that THERM pin has been pulled low by an external source.
6
D1 Fault
Read only
Short or OpenCircuit Sensor Diode D1.
7
D2 Fault
Read only
Short or OpenCircuit Sensor Diode D2.
1. Any time the Status Register is read out, the conditions (i.e., Register) that are read are automatically reset. In the case of the channel priority
indication, if two or more channels were out of limits, then another indication would automatically be generated if it was not handled during
the ISR.
2. In the Mask Register, the errant voltage interrupt may be disabled until the operator has time to clear the errant condition or set the limit
higher/lower.
相關PDF資料
PDF描述
PIC18LF46K80-I/P MCU PIC ECAN 64KB FLASH 40DIP
MS27468E13B22S CONN RCPT 22POS JAM NUT W/SCKT
VE-B4F-IW-F1 CONVERTER MOD DC/DC 72V 100W
PIC16LC620-04/SO IC MCU OTP 512X14 COMP 18SOIC
VE-B4D-IX-F4 CONVERTER MOD DC/DC 85V 75W
相關代理商/技術參數
參數描述
ADM1024ARUZ-REEL7 功能描述:IC MONITOR SYS TEMP/VOLT 24TSSOP RoHS:是 類別:集成電路 (IC) >> 接口 - 專用 系列:- 標準包裝:3,000 系列:- 應用:PDA，便攜式音頻/視頻，智能電話 接口:I²C，2 線串口 電源電壓:1.65 V ~ 3.6 V 封裝/外殼:24-WQFN 裸露焊盤 供應商設備封裝:24-QFN 裸露焊盤（4x4） 包裝:帶卷 (TR) 安裝類型:表面貼裝 產品目錄頁面:1015 (CN2011-ZH PDF) 其它名稱:296-25223-2
ADM1024EVB 功能描述:BOARD EVAL FOR ADM1024 RoHS:否 類別:編程器，開發系統 >> 過時/停產零件編號 系列:- 標準包裝:1 系列:- 傳感器類型:CMOS 成像，彩色（RGB） 傳感范圍:WVGA 接口:I²C 靈敏度:60 fps 電源電壓:5.7 V ~ 6.3 V 嵌入式:否 已供物品:成像器板 已用 IC / 零件:KAC-00401 相關產品:4H2099-ND - SENSOR IMAGE WVGA COLOR 48-PQFP4H2094-ND - SENSOR IMAGE WVGA MONO 48-PQFP
ADM1025 制造商:AD 制造商全稱:Analog Devices 功能描述:Low-Cost PC Hardware Monitor ASIC
ADM1025A 制造商:AD 制造商全稱:Analog Devices 功能描述:Low-Cost PC Hardware Monitor ASIC
ADM1025AARQ 功能描述:IC MONITOR SYS/VOLT 5CH 16QSOP RoHS:否 類別:集成電路 (IC) >> 接口 - 專用 系列:- 標準包裝:3,000 系列:- 應用:PDA，便攜式音頻/視頻，智能電話 接口:I²C，2 線串口 電源電壓:1.65 V ~ 3.6 V 封裝/外殼:24-WQFN 裸露焊盤 供應商設備封裝:24-QFN 裸露焊盤（4x4） 包裝:帶卷 (TR) 安裝類型:表面貼裝 產品目錄頁面:1015 (CN2011-ZH PDF) 其它名稱:296-25223-2
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*