參數資料
型號: ADL5372
廠商: Analog Devices, Inc.
英文描述: 300 MHz to 1000 MHz Quadrature Modulator
中文描述: 300 MHz到1000 MHz的正交調制器
文件頁數: 10/20頁
文件大?。?/td> 904K
代理商: ADL5372
ADL5370
THEORY OF OPERATION
CIRCUIT DESCRIPTION
Overview
The ADL5370 can be divided into five circuit blocks: the local
oscillator (LO) interface, the baseband voltage-to-current(V-to-I)
converter, the mixers, the differential-to-single-ended (D-to-S)
amplifier, and the bias circuit. A detailed block diagram of the
device is shown in Figure 24.
Rev. 0 | Page 10 of 20
PHASE
SPLITTER
OUT
LOIP
LOIN
IBBP
IBBN
QBBP
QBBN
Σ
0
Figure 24. Block Diagram
The LO interface generates two LO signals in quadrature. These
signals are used to drive the mixers. The I and Q baseband input
signals are converted to currents by the V-to-I stages, which
then drive the two mixers. The outputs of these mixers combine
to feed the differential-to-single-ended amplifier, which
provides a 50 Ω output interface. The bias cell generates
reference currents for the V-to-I stage and the D-to-S amplifier.
LO Interface
The LO interface consists of a polyphase quadrature splitter
followed by a limiting amplifier. The LO input impedance is set
by the polyphase. The LO can be driven either single-ended or
differentially. When driven single-ended, the LOIN pin should
be ac-grounded via a capacitor. Each quadrature LO signal then
passes through a limiting amplifier that provides the mixer with
a limited drive signal.
V-to-I Converter
The differential baseband inputs (QBBP, QBBN, IBBN, IBBP)
consist of the bases of PNP transistors, which present a high
impedance. The voltages applied to these pins drive the V-to-I
stage that converts baseband voltages into currents. The differential
output currents of the V-to-I stages feed each of their respective
Gilbert-cell mixers. The dc common-mode voltage at the baseband
inputs sets the currents in the two mixer cores. Varying the
baseband common-mode voltage varies the current in the mixer
and affects overall modulator performance. The recommended
dc voltage for the baseband common-mode voltage is 500 mV dc.
Mixers
The ADL5370 has two double-balanced mixers: one for the in-
phase channel (I channel) and one for the quadrature channel
(Q channel). Both mixers are based on the Gilbert-cell design of
four cross-connected transistors. The output currents from the
two mixers sum together into a load. The signal developed
across this load is used to drive the D-to-S amplifier.
D-to-S Amplifier
The output D-to-S amplifier consists of a totem pole output
stage. The 50 Ω output impedance is established by an on-chip
resistor. The D-to-S output is internally dc-biased and should be
ac-coupled at its output (VOUT).
Bias Circuit
An on-chip band gap reference circuit is used to generate a
proportional-to-absolute temperature (PTAT) reference current
for the V-to-I stage and a temperature independent current for
the D-to-S output stage.
相關PDF資料
PDF描述
ADL5373 300 MHz to 1000 MHz Quadrature Modulator
ADL5374 300 MHz to 1000 MHz Quadrature Modulator
ADL5385 300 MHz to 1000 MHz Quadrature Modulator
ADL5370 300 MHz to 1000 MHz Quadrature Modulator
ADL5370ACPZ-R2 300 MHz to 1000 MHz Quadrature Modulator
相關代理商/技術參數
參數描述
ADL5372ACPZ-R2 制造商:Analog Devices 功能描述:1500 MHZ TO 2500 MHZ QUADRATURE MODULATOR - Tape and Reel
ADL5372ACPZ-R21 制造商:AD 制造商全稱:Analog Devices 功能描述:1500 MHz to 2500 MHz Quadrature Modulator
ADL5372ACPZ-R7 功能描述:IC QUADRA MOD 1.5/2.5GHZ 24LFCSP RoHS:是 類別:RF/IF 和 RFID >> RF 調制器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 功能:調制器 LO 頻率:700MHz ~ 2.3GHz RF 頻率:700MHz ~ 2.3GHz P1dB:1dBm 底噪:-148dBm/Hz 輸出功率:-1dBm 電流 - 電源:46mA 電源電壓:2.7 V ~ 3.6 V 測試頻率:1.75GHz 封裝/外殼:28-WFQFN 裸露焊盤 包裝:帶卷 (TR)
ADL5372ACPZ-R71 制造商:AD 制造商全稱:Analog Devices 功能描述:1500 MHz to 2500 MHz Quadrature Modulator
ADL5372ACPZ-WP 制造商:Analog Devices 功能描述:QUADRATURE MOD 700MHZ 24LFCSP EP - Waffle Pack