參數資料
型號： ADF4150BCPZ-RL7
廠商： Analog Devices Inc
文件頁數： 11/28頁
文件大?。?/td> 0K
描述： IC PLL FREQ SYNTH 5.0GHZ 24LFCSP
標準包裝： 1,500
類型： 分?jǐn)?shù) N，整數 N，頻率合成器（RF）
PLL： 是
輸入： CMOS，TTL
輸出： 時鐘
電路數： 1
比率 - 輸入:輸出： 2:2
差分 - 輸入:輸出： 是/是
頻率 - 最大： 4.4GHz
除法器/乘法器： 是/無
電源電壓： 3 V ~ 3.6 V
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 24-WFQFN 裸露焊盤，CSP
供應商設備封裝： 24-LFCSP-WQ（4x4）
包裝： 帶卷 (TR)
Data Sheet
ADF4150
Rev. A | Page 19 of 28
MUXOUT
The on-chip multiplexer is controlled by Bits[DB28:DB26] (see
Reference Doubler
Setting DB25 to 0 feeds the REFIN signal directly to the 10-bit
R counter, disabling the doubler. Setting this bit to 1 multiplies
the REFIN frequency by a factor of 2 before feeding into the
10-bit R counter. When the doubler is disabled, the REFIN
falling edge is the active edge at the PFD input to the fractional
synthesizer. When the doubler is enabled, both the rising and
falling edges of REFIN become active edges at the PFD input.
When the doubler is enabled and the lowest spur mode is
chosen, the in-band phase noise performance is sensitive to the
REFIN duty cycle. The phase noise degradation can be as much
as 5 dB for the REFIN duty cycles outside a 45% to 55% range.
The phase noise is insensitive to the REFIN duty cycle in the
lowest noise mode. The phase noise is insensitive to the REFIN
duty cycle when the doubler is disabled.
The maximum allowable REFIN frequency when the doubler is
enabled is 30 MHz.
RDIV2
Setting the DB24 bit to 1 inserts a divide-by-2 toggle flip-flop
between the R counter and PFD, which extends the maximum
REFIN input rate. This function allows a 50% duty cycle signal
to appear at the PFD input, which is necessary for cycle slip
reduction.
10-Bit R Counter
The 10-bit R counter allows the input reference frequency
(REFIN) to be divided down to produce the reference clock to
the PFD. Division ratios from 1 to 1023 are allowed.
Double Buffer
DB13 enables or disables double buffering of Bits[DB22:DB20]
in Register 4. The Divider Select section explains how double
buffering works.
Current Setting
Bits[DB12:DB9] set the charge pump current setting. This
should be set to the charge pump current that the loop filter
is designed with (see Figure 22).
LDF
Setting DB8 to 1 enables integer-N digital lock detect, when
the FRAC part of the divider is zero; setting DB8 to 0 enables
fractional-N digital lock detect.
Lock Detect Precision (LDP)
When DB7 is set to 0, the fractional-N digital lock detect is
activated. In this case after setting DB7 to 0, 40 consecutive PFD
cycles of 10 ns must occur before digital lock detect is set. When
DB7 is programmed to 1, 40 consecutive reference cycles of 6 ns
must occur before digital lock detect goes high. Setting DB8 to 1
causes the activation of the integer-N digital lock detect. In this
case, after setting DB7 to 0, 5 consecutive cycles of 10 ns must
occur before digital lock detect is set. When DB7 is set to 1, five
consecutive cycles of 6 ns must occur.
Phase Detector Polarity
DB6 sets the phase detector polarity. When a passive loop filter,
or noninverting active loop filter is used, set this bit to 1. If an
active filter with an inverting characteristic is used, this bit
should be set to 0.
Power-Down (PD)
DB5 provides the programmable power-down mode. Setting this
bit to 1 performs a power-down. Setting this bit to 0 returns the
synthesizer to normal operation. When in software power-down
mode, the part retains all information in its registers. Only if the
supply voltages are removed are the register contents lost.
When a power-down is activated, the following events occur:
The synthesizer counters are forced to their load state
conditions.
The charge pump is forced into three-state mode.
The digital lock detect circuitry is reset.
The RFOUT buffers are disabled.
The input register remains active and capable of loading
and latching data.
Charge Pump (CP) Three-State
DB4 puts the charge pump into three-state mode when
programmed to 1. It should be set to 0 for normal operation.
Counter Reset
DB3 is the R counter and N counter reset bit for the ADF4150.
When this bit is 1, the RF synthesizer N counter and R counter
are held in reset. For normal operation, this bit should be set to 0.
相關PDF資料
PDF描述
ADF4150HVBCPZ IC FRACTION-N FREQ SYNTH 32LFCSP
ADF4151BCPZ-RL7 IC FRACTION-N FREQ SYNTH 32LFCSP
ADF4153YRUZ IC SYNTH PLL RF F-N FREQ 16TSSOP
ADF4154BRU IC FRAC-N FREQ SYNTH 16-TSSOP
ADF4156BRUZ-RL7 IC PLL FRAC-N FREQ SYNTH 16TSSOP
相關代理商/技術參數
參數描述
ADF4150HV 制造商:AD 制造商全稱:Analog Devices 功能描述:High Voltage, Fractional-N
ADF4150HVBCPZ 功能描述:IC FRACTION-N FREQ SYNTH 32LFCSP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 時鐘發生器，PLL，頻率合成器 系列:- 標準包裝:1,000 系列:Precision Edge® 類型:時鐘/頻率合成器 PLL:無 輸入:CML，PECL 輸出:CML 電路數:1 比率 - 輸入:輸出:2:1 差分 - 輸入:輸出:是/是 頻率 - 最大:10.7GHz 除法器/乘法器:無/無 電源電壓:2.375 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-VFQFN 裸露焊盤，16-MLF? 供應商設備封裝:16-MLF?（3x3） 包裝:帶卷 (TR) 其它名稱:SY58052UMGTRSY58052UMGTR-ND
ADF4150HVBCPZ-RL7 功能描述:IC FRACTION-N FREQ SYNTH 32LFCSP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 時鐘發生器，PLL，頻率合成器 系列:- 標準包裝:1,000 系列:Precision Edge® 類型:時鐘/頻率合成器 PLL:無 輸入:CML，PECL 輸出:CML 電路數:1 比率 - 輸入:輸出:2:1 差分 - 輸入:輸出:是/是 頻率 - 最大:10.7GHz 除法器/乘法器:無/無 電源電壓:2.375 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-VFQFN 裸露焊盤，16-MLF? 供應商設備封裝:16-MLF?（3x3） 包裝:帶卷 (TR) 其它名稱:SY58052UMGTRSY58052UMGTR-ND
ADF4151 制造商:AD 制造商全稱:Analog Devices 功能描述:Fractional-N/Integer-N PLL Synthesizer
ADF4151BCPZ 功能描述:IC PLL FREQ SYNTHESIZER 32LFCSP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 時鐘發生器，PLL，頻率合成器 系列:- 標準包裝:1,000 系列:Precision Edge® 類型:時鐘/頻率合成器 PLL:無 輸入:CML，PECL 輸出:CML 電路數:1 比率 - 輸入:輸出:2:1 差分 - 輸入:輸出:是/是 頻率 - 最大:10.7GHz 除法器/乘法器:無/無 電源電壓:2.375 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-VFQFN 裸露焊盤，16-MLF? 供應商設備封裝:16-MLF?（3x3） 包裝:帶卷 (TR) 其它名稱:SY58052UMGTRSY58052UMGTR-ND
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*