參數資料
型號: ADE7759ARSRL
廠商: ANALOG DEVICES INC
元件分類: 模擬信號調理
英文描述: Active Energy Metering IC with di/dt Sensor Interface
中文描述: SPECIALTY ANALOG CIRCUIT, PDSO20
封裝: SSOP-20
文件頁數: 20/32頁
文件大小: 530K
代理商: ADE7759ARSRL
REV. 0
ADE7759
–20–
0
0
1
1
1
1
1
1
7
0
1
PGA1
V1P
V1N
V1
ADC 1
HPF
20
PGA2
V2P
V2N
V2
ADC 2
DELAY BLOCK
1.12 s/LSB
20
LPF2
V2
V1
60Hz
0.1
V1
V2
CHANNEL 2 DELAY
REDUCED BY 4.48 s
(0.1 LEAD AT 60Hz)
FCH IN PHCAL [7:0]
PHCAL [7:0]
110 s TO +103 s
60Hz
Figure 28. Phase Calibration
FREQUENCY
Hz
0.30
100
P
0.25
0.20
0.15
0.10
0.05
0.00
0.05
0.10
200
300
400
500
600
700
800
900
1000
Figure 29. Combined Phase Response of the HPF and
Phase Compensation (10 Hz to 1 kHz)
FREQUENCY
Hz
0.30
40
P
0.25
0.20
0.15
0.10
0.05
0.00
0.05
0.10
45
50
55
60
65
70
Figure 30. Combined Phase Response of the HPF and
Phase Compensation (40 Hz to 70 Hz)
FREQUENCY
Hz
0.4
E
54
56
58
60
62
64
66
0.3
0.2
0.1
0.0
0.1
0.2
0.3
0.4
Figure 31. Combined Gain Response of the HPF and Phase
Compensation (Deviation of Gain in % from Gain at 60 Hz)
ACTIVE POWER CALCULATION
Electrical power is defined as the rate of energy flow from
source to load. It is given by the product of the voltage and current
waveforms. The resulting waveform is called the instantaneous
power signal, and it is equal to the rate of energy flow at every
instant of time. The unit of power is the watt or joules/second
Equation 3 gives an expression for the instantaneous power signal
in an ac system.
v t
i t
V
t
( )
(
)
=
2
ω
(1)
I
t
( )
sin(
)
=
2
ω
(2)
where
V
= rms voltage,
I
= rms current.
p t
p t
VI
( )
=
The average power over an integral number of line cycles (n) is
given by the expression in Equation 4.
1
( )
v t
( )
i t
( )
cos(
VI
t
( )
)
=
×
2
ω
(3)
P
nT
p t dt
VI
nT
0
=
=
(4)
where
T
is the line cycle period.
P
is referred to as the Active or
Real Power. Note that the active power is equal to the dc com-
ponent of the instantaneous power signal
p(t)
in Equation 3, i.e.,
VI. This is the relationship used to calculate active power in the
ADE7759. The instantaneous power signal p(t) is generated by
multiplying the current and voltage signals. The dc component of
the instantaneous power signal is then extracted by LPF2
(Low-Pass Filter) to obtain the active power information. This
process is illustrated graphically in Figure 32. Since LPF2 does not
have an ideal “brick wall” frequency response (see Figure 33),
the Active Power signal will have some ripple due to the instanta-
neous power signal. This ripple is sinusoidal and has a frequency
equal to twice the line frequency. Since the ripple is sinusoidal
in nature it will be removed when the Active Power signal is
integrated to calculate Energy—see Energy Calculation section.
相關PDF資料
PDF描述
ADE7759ARS 8-Channel 14-Bit Single-Supply Voltage-Output DAC; Package: LQFP (10x10mm); No of Pins: 52; Temperature Range: Industrial
ADE7759 Active Energy Metering IC with di/dt Sensor Interface
ADE7760ARSRL Energy Metering IC with On-Chip Fault Detection
ADE7760 8-Channel 14-Bit Single-Supply Voltage-Output DAC; Package: LQFP (10x10mm); No of Pins: 52; Temperature Range: Industrial
ADE7760ARS Energy Metering IC with On-Chip Fault Detection
相關代理商/技術參數
參數描述
ADE7759ARSZ 功能描述:IC ENERGY METERING 1PHASE 20SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 能量測量 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:*
ADE7759ARSZRL 功能描述:IC ENERGY METERING 1PHASE 20SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 能量測量 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:*
ADE7760 制造商:AD 制造商全稱:Analog Devices 功能描述:Energy Metering IC with On-Chip Fault Detection
ADE7760ARS 制造商:Analog Devices 功能描述:Energy Measurement 20-Pin SSOP 制造商:Analog Devices 功能描述:ENERGY METER IC W/ ONCHIP FAULT & OSCIL. - Rail/Tube
ADE7760ARSRL 制造商:Analog Devices 功能描述:Energy Measurement 20-Pin SSOP T/R 制造商:Analog Devices 功能描述:ENERGY METER IC W/ONCHIP FAULT & OSCIL. - Tape and Reel