參數資料
型號： ADADC80-Z-12
廠商： Analog Devices Inc
文件頁數： 4/16頁
文件大?。?/td> 0K
描述： IC ADC 12BIT INTEGRATED 32-CDIP
標準包裝： 1
位數： 12
采樣率（每秒）： 40k
數據接口： 并聯
轉換器數目： 1
功率耗散（最大）： 800mW
電壓電源： 模擬和數字，雙 ±
工作溫度： -25°C ~ 85°C
安裝類型： 通孔
封裝/外殼： 32-CDIP（0.910"，23.12mm）
供應商設備封裝： 32-CDIP 側面銅焊
包裝： 管件
輸入數目和類型： 2 個單端，單極；2 個單端，雙極
ADADC80
Rev. E | Page 12 of 16
Other Ranges
Coding relationships and calibration points for 0 V to +5 V,
2.5 V to +2.5 V, and 5 V to +5 V ranges can be found by
halving the corresponding code equivalents listed for the 0 V to
+10 V and 10 V to +10 V ranges, respectively.
Zero and full-scale calibration can be accomplished to a
precision of approximately ±1/4 LSB using the static adjustment
procedure described previously. By summing a small sine- or
triangular-wave voltage with the signal applied to the analog
input, the output can be cycled through each of the calibration
codes of interest to more accurately determine the center (or
end points) of each discrete quantization level. A detailed
description of this dynamic calibration technique is presented
in A/D Conversion Notes, D. Sheingold, Analog Devices, Inc.,
1977, Part II, Chapter 3.
GROUNDING
Many data-acquisition components have two or more ground
pins that are not connected together within the device. These
grounds are usually referred to as the logic power return, analog
common (analog power return), and analog signal ground.
These grounds must be tied together at one point, usually at the
system power-supply ground. Ideally, a single solid ground is
desirable. However, because current flows through the ground
wires and etch stripes of the circuit cards, and because these
paths have resistance and inductance, hundreds of millivolts can
be generated between the system ground point and the ground
pin of the ADADC80. Therefore, separate ground returns
should be provided to minimize the current flow in the path
from sensitive points to the system ground point, and the two
device grounds should be tied together. In this way, supply
currents and logic gate return currents are not summed into the
same return path as analog signals, where they would cause
measurement errors.
Each of the ADADC80 supply terminals should be capacitively
decoupled as close to the ADADC80 as possible. A large value
capacitor, such as 1 μF in parallel with a 0.1 μF capacitor, is
usually sufficient. Analog supplies are bypassed to the analog
power return pin, and the logic supply is bypassed to the logic
power return pin.
17
15
25
10
9
ADADC80
AD583
SAMPLE AND
HOLD
*ANALOG
GROUND
AD521
INST. AMP
OUTPUT
REFERENCE
0.01
F
0.01
F
0.01
F
0.01
F
0.01
F
0.01
F
0.01
F
DIG
COM
5V
C
–15V
C
+15V
ANALOG
PS
DIGITAL
PS
*IF INDEPENDENT, OTHERWISE RETURN
AMPLIFIER REFERENCE TO MECCA AT
ANALOG P.S. COMMON.
0
120
2-
0
15
15V OR
12V
–15V OR
–12V
ANALOG
GND
DIGITAL
GND
5V
DIGITAL
SUPPLY
DIGITAL
GROUND
Figure 15. Basic Grounding Practice
相關PDF資料
PDF描述
ADATE207BBPZ IC TIMING FORMATTER QUAD 256BGA
ADC0804LCN IC ADC 8-BIT 10KSPS 1LSB 20-DIP
ADC0820CCM+ IC ADC 8-BIT HS 20-SOIC
ADF4001BRU IC CLOCK GEN PLL 16-TSSOP
ADF4002BRUZ-RL7 IC PLL FREQUENCY SYNTH 16-TSSOP
相關代理商/技術參數
參數描述
ADADC80Z-12 制造商:AD 制造商全稱:Analog Devices 功能描述:Analog-to-Digital Converter， 12-Bit
ADADC80Z-CBI-V 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:Analog Devices 功能描述:
adadc80z-ccd-i 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:Analog Devices 功能描述:
ADADC-816BD 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog-to-Digital Converter， 10-Bit
ADADC-816KD 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog-to-Digital Converter， 10-Bit
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*