參數資料
型號： AD9709ASTZ
廠商： Analog Devices Inc
文件頁數： 7/32頁
文件大?。?/td> 0K
描述： IC DAC 8BIT DUAL 125MSPS 48-LQFP
產品培訓模塊： Data Converter Fundamentals
DAC Architectures
標準包裝： 1
系列： TxDAC+®
設置時間： 35ns
位數： 8
數據接口： 并聯
轉換器數目： 2
電壓電源： 模擬和數字
功率耗散（最大）： 450mW
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 48-LQFP
供應商設備封裝： 48-LQFP（7x7）
包裝： 托盤
輸出數目和類型： 4 電流，單極；4 電流，雙極
采樣率（每秒）： 125M
產品目錄頁面： 785 (CN2011-ZH PDF)
配用： AD9709-EBZ-ND - BOARD EVAL FOR AD9709
AD9709
Rev. B | Page 15 of 32
DIGITAL INPUTS
The digital inputs of the AD9709 consist of two independent
channels. For the dual port mode, each DAC has its own
dedicated 8-bit data port: WRT line and CLK line. In the
interleaved timing mode, the function of the digital control pins
changes as described in the Interleaved Mode Timing section.
The 8-bit parallel data inputs follow straight binary coding
where DB7P1 and DB7P2 are the most significant bits (MSBs)
and DB0P1 and DB0P2 are the least significant bits (LSBs).
IOUTA produces a full-scale output current when all data bits are
at Logic 1. IOUTB produces a complementary output with the
full-scale current split between the two outputs as a function of
the input code.
The digital interface is implemented using an edge-triggered
master slave latch. The DAC outputs are updated following
either the rising edge or every other rising edge of the clock,
depending on whether dual or interleaved mode is used. The
DAC outputs are designed to support a clock rate as high as
125 MSPS. The clock can be operated at any duty cycle that
meets the specified latch pulse width. The setup and hold times
can also be varied within the clock cycle as long as the specified
minimum times are met, although the location of these transition
edges may affect digital feedthrough and distortion performance.
Best performance is typically achieved when the input data
transitions on the falling edge of a 50% duty cycle clock.
DAC TIMING
The AD9709 can operate in two timing modes, dual and
interleaved, which are described in the following sections. The
block diagram in Figure 25 represents the latch architecture in
the interleaved timing mode.
IQSEL
IQWRT
DAC1
INTERLEAVED
DATA IN, PORT 1
IQCLK
IQRESET
DAC2
÷2
PORT 1
INPUT
LATCH
PORT 2
INPUT
LATCH
DEINTERLEAVED
DATA OUT
DAC1
LATCH
DAC2
LATCH
00
60
6-
0
27
Figure 25. Latch Structure in Interleaved Mode
Dual Port Mode Timing
When the MODE pin is at Logic 1, the AD9709 operates in dual
port mode (refer to Figure 21). The AD9709 functions as two
distinct DACs. Each DAC has its own completely independent
digital input and control lines.
The AD9709 features a double-buffered data path. Data enters the
device through the channel input latches. This data is then trans-
ferred to the DAC latch in each signal path. After the data is loaded
into the DAC latch, the analog output settles to its new value.
For general consideration, the WRT lines control the channel
input latches, and the CLK lines control the DAC latches. Both
sets of latches are updated on the rising edge of their respective
control signals.
The rising edge of CLK should occur before or simultaneously
with the rising edge of WRT. If the rising edge of CLK occurs
after the rising edge of WRT, a minimum delay of 2 ns should
be maintained from rising edge of WRT to rising edge of CLK.
Timing specifications for dual port mode are given in Figure 26
DATA IN
WRT1/WRT2
CLK1/CLK2
tPD
IOUTA
OR
IOUTB
tS
tH
tLPW
tCPW
00
60
6-
0
25
Figure 26. Dual Port Mode Timing
DATA IN
WRT1/WRT2
CLK1/CLK2
XX
D1
D2
D3
D4
IOUTA
OR
IOUTB
D1
D2
D3
D4
D5
00
60
6-
02
6
Figure 27. Dual Mode Timing
Interleaved Mode Timing
When the MODE pin is at Logic 0, the AD9709 operates in
interleaved mode (refer to Figure 25). In addition, WRT1
functions as IQWRT, CLK1 functions as IQCLK, WRT2
functions as IQSEL, and CLK2 functions as IQRESET.
Data enters the device on the rising edge of IQWRT. The
logic level of IQSEL steers the data to either Channel Latch 1
(IQSEL = 1) or to Channel Latch 2 (IQSEL = 0). For proper
operation, IQSEL should only change state when IQWRT and
IQCLK are low.
When IQRESET is high, IQCLK is disabled. When IQRESET
goes low, the next rising edge on IQCLK updates both DAC
latches with the data present at their inputs. In the interleaved
mode, IQCLK is divided by 2 internally. Following this first
rising edge, the DAC latches are only updated on every other
rising edge of IQCLK. In this way, IQRESET can be used to
synchronize the routing of the data to the DACs.
Similar to the order of CLK and WRT in dual port mode,
IQCLK should occur before or simultaneously with IQWRT.
相關PDF資料
PDF描述
MS27467T25F19PD CONN PLUG 19POS STRAIGHT W/PINS
MS27466T25B29SB CONN RCPT 29POS WALL MT W/SCKT
AD7392ARZ IC DAC 12BIT PARALLEL 3V 20-SOIC
VE-J03-MZ-F4 CONVERTER MOD DC/DC 24V 25W
VE-J03-MZ-F3 CONVERTER MOD DC/DC 24V 25W
相關代理商/技術參數
參數描述
AD9709ASTZ1 制造商:AD 制造商全稱:Analog Devices 功能描述:8-Bit, 125 MSPS, Dual TxDAC Digital-to-Analog Converter
AD9709ASTZKL1 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述:
AD9709ASTZRL 功能描述:IC DAC 8BIT DUAL 125MSPS 48LQFP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:TxDAC+® 產品培訓模塊:LTC263x 12-, 10-, and 8-Bit VOUT DAC Family 特色產品:LTC2636 - Octal 12-/10-/8-Bit SPI VOUT DACs with 10ppm/°C Reference 標準包裝:91 系列:- 設置時間:4µs 位數:10 數據接口:MICROWIRE?，串行，SPI? 轉換器數目:8 電壓電源:單電源 功率耗散（最大）:2.7mW 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-WFDFN 裸露焊盤 供應商設備封裝:14-DFN-EP（4x3） 包裝:管件 輸出數目和類型:8 電壓，單極 采樣率（每秒）:*
AD9709ASTZRL1 制造商:AD 制造商全稱:Analog Devices 功能描述:8-Bit, 125 MSPS, Dual TxDAC Digital-to-Analog Converter
AD9709-EB 制造商:Analog Devices 功能描述: 制造商:Rochester Electronics LLC 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*