- 您現在的位置：買賣IC網 > PDF目錄10654 > AD9484BCPZ-500 (Analog Devices Inc)IC ADC 8BIT 500MSPS 56LFCSP PDF資料下載
參數資料
| 型號： | AD9484BCPZ-500 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 10/24頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 8BIT 500MSPS 56LFCSP |
| 標準包裝： | 1 |
| 位數： | 8 |
| 采樣率（每秒）： | 500M |
| 數據接口： | 串行，SPI? |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 720mW |
| 電壓電源： | 模擬和數字 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 56-VFQFN 裸露焊盤，CSP |
| 供應商設備封裝： | 56-LFCSP-VQ（8x8） |
| 包裝： | 托盤 |
| 輸入數目和類型： | 1 個差分，雙極 |
AD9484
Rev. A | Page 18 of 24
AD9484 CONFIGURATION USING THE SPI
The AD9484 SPI allows the user to configure the converter for
specific functions or operations through a structured register
space inside the ADC. This gives the user added flexibility to
customize device operation depending on the application.
Addresses are accessed (programmed or readback) serially in
1-byte words. Each byte can be further divided into fields,
which are documented in the Memory Map section.
There are three pins that define the serial port interface (SPI) to
this particular ADC. They are the SCLK/DFS, SDIO and CSB
pins. The SCLK/DFS (serial clock) is used to synchronize the
read and write data presented the ADC. The SDIO (serial data
input/output) is a dual-purpose pin that allows data to be sent
to and read from the internal ADC memory map registers. The
CSB is an active low control that enables or disables the read
and write cycles (see Table 8).
Table 8. Serial Port Pins
Mnemonic
Function
SCLK
SCLK (serial clock) is the serial shift clock in.
SCLK is used to synchronize serial interface
reads and writes.
SDIO
SDIO (serial data input/output) is a dual-purpose
pin. The typical role for this pin is an input and
output depending on the instruction being sent
and the relative position in the timing frame.
CSB
CSB (chip select) is an active low control that
gates the read and write cycles.
The falling edge of the CSB, in conjunction with the rising edge
of the SCLK, determines the start of the framing. An example of
the serial timing and its definitions can be found in Figure 39
and Table 10.
During an instruction phase, a 16-bit instruction is transmitted.
Data then follows the instruction phase and is determined by
the W0 and W1 bits, which is one or more bytes of data. All
data is composed of 8-bit words. The first bit of each individual
byte of serial data indicates whether this is a read or write
command. This allows the serial data input/output (SDIO) pin
to change direction from an input to an output.
Data can be sent in MSB or in LSB first mode. MSB first is
default on power-up and can be changed by changing the
configuration register. For more information about this feature
and others, see the AN-877 Application Note, Interfacing to
High Speed ADCs via SPI at www.analog.com.
HARDWARE INTERFACE
The pins described in Table 8 comprise the physical interface
between the programming device of the user and the serial port
of the AD9484. The SCLK pin and the CSB pin function as
inputs when using the SPI interface. The SDIO pin is bidirec-
tional, functioning as an input during the write phase and as an
output during readback.
This interface is flexible enough to be controlled by either
PROMs or PIC microcontrollers as well. This provides the user
with an alternate method to program the ADC other than a SPI
controller.
If the user chooses not to use the SPI interface, some pins serve
a dual function and are associated with a specific function when
strapped externally to AVDD or ground during device power-
on. The Configuration Without the SPI section describes the
strappable functions supported on the AD9484.
CONFIGURATION WITHOUT THE SPI
In applications that do not interface to the SPI control registers,
the SCLK/DFS pin can alternately serve as a standalone CMOS-
compatible control pin. Connect the CSB pin to AVDD, which
disables the serial port interface.
Table 9. Mode Selection
Mnemonic
External
Voltage
Configuration
AVDD
Twos complement enabled
SCLK/DFS
AGND
Offset binary enabled
DON’T CARE
CSB
tS
tDH
tHIGH
tCLK
tLOW
tDS
tH
R/W
W1
W0
A12
A11
A10
A9
A8
A7
D5
D4
D3
D2
D1
D0
SDIO DON’T CARE
SCLK DON’T CARE
096
15-
0
23
Figure 39. Serial Port Interface Timing Diagram
相關PDF資料 |
PDF描述 |
|---|---|
| MAX996ESD+T | IC COMPARATOR R-R 14-SOIC |
| VI-21M-IW-F1 | CONVERTER MOD DC/DC 10V 100W |
| VE-B1K-MX-F3 | CONVERTER MOD DC/DC 40V 75W |
| LTC2252IUH#PBF | IC ADC 12-BIT 105MSPS 3V 32-QFN |
| MAX995EUD+T | IC COMPARATOR R-R 14-TSSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9484BCPZRL7-500 | 功能描述:IC ADC 8BIT 500MSPS 56LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
| AD9500 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Digitally Programmable Delay Generator |
| AD9500BP | 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述: |
| AD9500BP-REEL | 制造商:Analog Devices 功能描述:Digitally Programmable Delay Generator 28-Pin PLCC T/R |
| AD9500BQ | 制造商:AD 制造商全稱:Analog Devices 功能描述:Digitally Programmable Delay Generator |
發布緊急采購，3分鐘左右您將得到回復。