- 您現在的位置：買賣IC網 > PDF目錄5427 > AD8628WAUJZ-RL (Analog Devices Inc)IC OPAMP CHOPPER R-R 5TSOT PDF資料下載
參數資料
| 型號： | AD8628WAUJZ-RL |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 11/24頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC OPAMP CHOPPER R-R 5TSOT |
| 設計資源： | Precision, Unipolar, Inverting Conversion Using AD5546/56 DAC (CN0022) Precision, Unipolar, Inverting Conversion Using AD5547/57 DAC (CN0026) Precision, Unipolar, Noninverting Configuration for the AD5547/57 DAC (CN0027) Precision, Unipolar, Noninverting Configuration for the AD5546/56 DAC (CN0023) High Precision Digital-to-Analog Conversion Using the 16-Bit AD5542/1, ADR421, and AD8628 (CN0079) |
| 標準包裝： | 10,000 |
| 放大器類型： | 零漂移 |
| 電路數： | 1 |
| 輸出類型： | 滿擺幅 |
| 轉換速率： | 1 V/µs |
| 增益帶寬積： | 2.5MHz |
| -3db帶寬： | 2.5MHz |
| 電流 - 輸入偏壓： | 30pA |
| 電壓 - 輸入偏移： | 1µV |
| 電流 - 電源： | 850µA |
| 電流 - 輸出 / 通道： | 30mA |
| 電壓 - 電源，單路/雙路(±)： | 2.7 V ~ 5 V，±1.35 V ~ 2.5 V |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | SOT-23-5 細型，TSOT-23-5 |
| 供應商設備封裝： | TSOT-23-5 |
| 包裝： | 帶卷 (TR) |
Data Sheet
AD8628/AD8629/AD8630
Rev. J | Page 19 of 24
PRECISION CURRENT SHUNT SENSOR
A precision current shunt sensor benefits from the unique
attributes of auto-zero amplifiers when used in a differencing
configuration, as shown in Figure 63. Current shunt sensors are
used in precision current sources for feedback control systems.
They are also used in a variety of other applications, including
battery fuel gauging, laser diode power measurement and control,
torque feedback controls in electric power steering, and precision
power metering.
RS
0.1
SUPPLY
I
RL
100
100k
5V
100
100k
e = 1000 RS I
100mV/mA
AD8628
02
73
5-
0
60
C
Figure 63. Low-Side Current Sensing
In such applications, it is desirable to use a shunt with very low
resistance to minimize the series voltage drop; this minimizes
wasted power and allows the measurement of high currents
while saving power. A typical shunt might be 0.1 Ω. At measured
current values of 1 A, the output signal of the shunt is hundreds
of millivolts, or even volts, and amplifier error sources are not
critical. However, at low measured current values in the 1 mA
range, the 100 μV output voltage of the shunt demands a very
low offset voltage and drift to maintain absolute accuracy. Low
input bias currents are also needed, so that injected bias current
does not become a significant percentage of the measured current.
High open-loop gain, CMRR, and PSRR help to maintain the
overall circuit accuracy. As long as the rate of change of the
current is not too fast, an auto-zero amplifier can be used with
excellent results.
OUTPUT AMPLIFIER FOR HIGH PRECISION DACS
a 16-bit high precision DAC in a unipolar configuration. In this
case, the selected op amp needs to have a very low offset voltage
(the DAC LSB is 38 μV when operated with a 2.5 V reference)
to eliminate the need for output offset trims. The input bias
current (typically a few tens of picoamperes) must also be very
low because it generates an additional zero code error when
multiplied by the DAC output impedance (approximately 6 kΩ).
Rail-to-rail input and output provide full-scale output with very
little error. The output impedance of the DAC is constant and
code independent, but the high input impedance of the AD8628/
AD8629/AD8630 minimizes gain errors. The wide bandwidth
of the amplifiers also serves well in this case. The amplifiers,
with settling time of 1 μs, add another time constant to the
system, increasing the settling time of the output. The settling
time of the AD5541 is 1 μs. The combined settling time is
approximately 1.4 μs, as can be derived from the following
equation:
2
2
AD8628
S
t
DAC
t
TOTAL
t
02
73
5-
0
61
AD5541/AD5542
AD8628
DGND
*AD5542 ONLY
VDD REF(REFF*) REFS*
VOUT
SCLK
DIN
CS
AGND
5V
2.5V
UNIPOLAR
OUTPUT
LDAC*
0.1F
10F
0.1F
SERIAL
INTERFACE
Figure 64. AD8628 Used as an Output Amplifier
相關PDF資料 |
PDF描述 |
|---|---|
| 52077-1 | TERM RING IR 12AWG #1/2 PIDG |
| TSW-134-08-S-D | CONN HEADER 68POS .100" DL GOLD |
| 51741-10006017AA | VERT REC POWERBLADE |
| 059-0112 | FUSE JOINT 5A 440V CYLINDRICAL |
| 059-0109 | FUSE JOINT 1A 440V CYLINDRICAL |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD8629 | 制造商:Analog Devices 功能描述:DUAL R-R CHOPPER OP - Bulk |
| AD8629AL-EMX | 制造商:Analog Devices 功能描述:- Bulk |
| AD8629ARMZ | 功能描述:IC OPAMP CHOPPER R-R DUAL 8MSOP RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:1 系列:- 放大器類型:通用 電路數:4 輸出類型:滿擺幅 轉換速率:0.028 V/µs 增益帶寬積:105kHz -3db帶寬:- 電流 - 輸入偏壓:3nA 電壓 - 輸入偏移:100µV 電流 - 電源:3.3µA 電流 - 輸出 / 通道:12mA 電壓 - 電源，單路/雙路(±):2.7 V ~ 12 V，±1.35 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:14-TSSOP 包裝:剪切帶 (CT) 其它名稱:OP481GRUZ-REELCT |
| AD8629ARMZ | 制造商:Analog Devices 功能描述:OPERATIONAL AMPLIFIER IC 制造商:Analog Devices 功能描述:OPAMP DUAL RRIO 2.5MHZ 1V/ 8MSOP 制造商:Analog Devices 功能描述:OPAMP, DUAL, RRIO, 2.5MHZ, 1V/S, 8MSOP |
| AD8629ARMZ-R2 | 制造商:Analog Devices 功能描述:SP Amp Chopper Stabilization Dual R-R I/O 制造商:Analog Devices 功能描述:SP Amp Chopper Stabilization Dual R-R I/O ±2.5V/5V 8-Pin MSOP T/R |
發布緊急采購，3分鐘左右您將得到回復。