參數資料
型號： AD8151ASTZ
廠商： Analog Devices Inc
文件頁數： 18/40頁
文件大?。?/td> 0K
描述： IC CROSSPOINT SWIT 33X17 184LQFP
標準包裝： 1
系列： XStream™
功能： 交叉點開關
電路： 1 x 33:17
電壓電源： 雙電源
電壓 - 電源，單路/雙路(±)： ±3 V ~ 5.25 V
工作溫度： 0°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 184-LQFP
供應商設備封裝： 184-LQFP（20x20）
包裝： 托盤
AD8151
Rev. B | Page 25 of 40
CONFIGURATION PROGRAMMING
The board is configurable by one of two methods. For ease of
use, custom software is provided that controls the AD8151
programming via the parallel port of a PC. This requires a
standard printer cable that has a DB-25 connector at one end
(parallel-port or printer-port interface) and a Centronix
connector at the other, which connects to P2 of the AD8151
evaluation board. The programming with this setup is serial, so
it is not the fastest way to configure the AD8151 matrix.
However, the user interface makes it very convenient to use this
programming method.
If a high speed programming interface is desired, the AD8151
address and data buses are directly available on P3. The source
of the program signals can be a piece of test equipment such as
the Tektronix HFS-9000 digital test generator or other hardware
that generates programming signals. When using the PC inter-
face, the jumper at W1 should be installed and no connections
should be made to P3. When using the P3 interface, no jumper
is installed at W1. There are locations for termination resistors
for the address and data signals, if needed.
SOFTWARE INSTALLATION
The software to operate the AD8151 is provided on two 3.5"
floppy disks. To install the software on a PC:
1.
Insert Disk 1 into the floppy disk drive.
2.
Run the setup.exe program. This program routinely installs
the software.
3.
Insert Disk 2 when prompted.
4.
Select a program directory when prompted.
After running the software, the user is prompted to identify
which of three software drivers is used with the PC parallel
port. The default is LPT1, which is most commonly used.
However, some laptops commonly use the PRN driver. It is also
possible that some systems are configured with the LPT2 driver.
If it is not known which driver is used, it is best to select LPT1
and proceed to the next screen, which displays the buttons that
allow the connection of inputs to outputs of the AD8151. All of
the outputs should be in the output off state after the program
starts running. Any of the active buttons can be selected by
clicking the mouse, which sends out a burst of programming
data.
After the software driver has been selected, the user can
generate a steady stream of programming signals out of the
parallel port by holding down the left or right arrow key on the
keyboard. The clock test point on the AD8151 evaluation board
can be monitored with an oscilloscope for any activity (a user-
supplied printer cable must be connected). If there is a square-
wave present, the proper software driver is selected for the PC’s
parallel port.
If there is no signal present, select another driver by clicking
Parallel Port
on the File menu. Select a different software
driver and carry out the test described previously until signal
activity is present at the clock test point.
相關PDF資料
PDF描述
AD8152JBP IC CROSSPOINT SWIT 34X34 256BGA
AD8153ACPZ-RL7 IC SW MUX/DEMUX SGL BUFF 32LFCSP
AD8155ACPZ IC MUX/DEMUX DUAL BUFFER 64LFCSP
AD8156ABCZ IC SWITCH XPT 4X4 W/EQ 49CSPBGA
AD8158ACPZ IC MUX/DEMUX QUAD 2X1 100LFCSP
相關代理商/技術參數
參數描述
AD8151-EVAL 制造商:Analog Devices 功能描述:EVAL KIT FOR 33 17, 3.2 GBPS DGTL CROSSPOINT SWIT - Bulk
AD8151XSTZ 功能描述:IC CROSSPOINT SWITCH 制造商:analog devices inc. 系列:* 零件狀態:上次購買時間 標準包裝:1
AD8152 制造商:AD 制造商全稱:Analog Devices 功能描述:34 x 34, 3.2 Gbps Asynchronous Digital Crosspoint Switch
AD8152-EVAL 制造商:Analog Devices 功能描述:EVAL KIT FOR ASYNCH DGTL CROSSPOINT SWIT - Bulk
AD8152JBP 功能描述:IC CROSSPOINT SWIT 34X34 256BGA RoHS:否 類別:集成電路 (IC) >> 接口 - 模擬開關，多路復用器，多路分解器 系列:XStream™ 其它有關文件:STG4159 View All Specifications 標準包裝:5,000 系列:- 功能:開關 電路:1 x SPDT 導通狀態電阻:300 毫歐 電壓電源:雙電源 電壓 - 電源，單路/雙路(±):±1.65 V ~ 4.8 V 電流 - 電源:50nA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:7-WFBGA，F(xiàn)CBGA 供應商設備封裝:7-覆晶 包裝:帶卷 (TR)
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*