參數資料
型號： AD8151ASTZ
廠商： Analog Devices Inc
文件頁數： 13/40頁
文件大?。?/td> 0K
描述： IC CROSSPOINT SWIT 33X17 184LQFP
標準包裝： 1
系列： XStream™
功能： 交叉點開關
電路： 1 x 33:17
電壓電源： 雙電源
電壓 - 電源，單路/雙路(±)： ±3 V ~ 5.25 V
工作溫度： 0°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 184-LQFP
供應商設備封裝： 184-LQFP（20x20）
包裝： 托盤
AD8151
Rev. B | Page 20 of 40
To ensure proper operation, all outputs (including unused
output) must be pulled high using external pull-up networks to
a level within the output compliance range. If outputs from
multiple AD8151s are wired together, a single pull-up network
can be used for each output bus. The pull-up network should be
chosen to keep the output voltage levels within the output
compliance range at all times. Recommended pull-up networks
to produce PECL/ECL 100 kΩ and 10 kΩ compatible outputs
are shown in Figure 36. Alternatively, a separate supply can be
used to provide VCOM, making RCOM and DCOM unnecessary.
02169-036
OUTyyN
OUTyyP
AD8151
OUTyyN
OUTyyP
AD8151
VCC
RL
VCC
RL
VCOM
RCOM
VCOM
DCOM
Figure 36. Output Pull-Up Networks for PECL/ECL: a) 100 kΩ and b) 10kΩ
The output levels are
VOH = VCOM
VOL = VCOM – IOUTRL
VSWING = VOH VOL = IOUTRL
VCOM = VCC – IOUTRCOM (100 kΩ mode)
VCOM = VCC – V(DCOM) (10 kΩ mode)
The common-mode adjustment element (RCOM or DCOM) can be
omitted if the input range of the receiver includes the positive
supply voltage. The bypass capacitors reduce common-mode
perturbations by providing an ac short from the common nodes
(VCOM) to ground. When busing together the outputs of
multiple AD8151s or when running at high data rates, double
termination of its outputs is recommended to mitigate the
impact of reflections due to open transmission line stubs and
the lumped capacitance of the AD8151 output pins. A possible
connection is shown in Figure 37; the bypass capacitors provide
an ac short from the common nodes of the termination resistors
to ground. To maintain signal fidelity at high data rates, the
stubs connecting the output pins to the output transmission
lines or load resistors should be as short as possible.
02169-037
RL
ZO
VCC
RCOM
VCOM
OUTyyN
OUTyyP
AD8151
OUTyyN
OUTyyP
AD8151
RECEIVER
Figure 37. Double Termination of AD8151 Outputs
In this case, the output levels are
VOH = VCOM – ()IOUTRL
VOL = VCOM – ()IOUTRL
VSWING = VOH – VOL = ()IOUTRL
Output Current Set Pin (REF)
A simplified schematic of the reference circuit is shown in
Figure 38. A single external resistor connected between the REF
pin and VEE determines the output current for all output stages.
This feature allows a choice of pull-up networks and trans-
mission line characteristic impedances while still achieving a
nominal output swing of 800 mV. At low data rates, substantial
power savings can be achieved by using lower output swings
and higher load resistances.
02169-038
RSET
VEE
VCC
IOUT/20
AD8151
REF
1.2V
Figure 38. Simplified Reference Circuit
The nominal output current is given by the following:
=
SET
R
V
2
.
1
20
OUT
I
The minimum set resistor is RSET, MIN = 960 Ω resulting in
IOUT, MAX = 25 mA. The maximum set resistor is RSET, MAX = 4.8 kΩ
resulting in IOUT, MIN = 5 mA. Nominal 800 mV differential
output swing can be achieved in a 50 Ω load using RSET = 1.5 kΩ
(IOUT = 16 mA), or in a doubly terminated 75 Ω load using
RSET = 1.13 kΩ (IOUT = 21.3 mA). To minimize stray capacitance
and avoid the pickup of unwanted signals, the external set
resistor should be located close to the REF pin. Bypassing the
set resistor is not recommended.
Power Supplies
There are several options for the power supply voltages for the
AD8151, as there are two separate sections of the chip that
require power supplies. These are the control logic and the high
speed data paths. Depending on the system architecture, the
voltage levels of these supplies can vary.
Logic Supplies
The control (programming) logic is CMOS and is designed to
interface with any of the standard single-ended logic families
(CMOS or TTL). Its supply voltage pins are VDD (Pin 170, logic
positive) and VSS (Pin 152, logic ground). In all cases the logic
ground should be connected to the system digital ground. VDD
should be supplied at between 3.3 V to 5 V to match the supply
voltage of the logic family that is used to drive the logic inputs.
VDD should be bypassed to ground with a 0.1 μF ceramic capa-
citor. The absolute maximum voltage from VDD to VSS is 5.5 V.
相關PDF資料
PDF描述
AD8152JBP IC CROSSPOINT SWIT 34X34 256BGA
AD8153ACPZ-RL7 IC SW MUX/DEMUX SGL BUFF 32LFCSP
AD8155ACPZ IC MUX/DEMUX DUAL BUFFER 64LFCSP
AD8156ABCZ IC SWITCH XPT 4X4 W/EQ 49CSPBGA
AD8158ACPZ IC MUX/DEMUX QUAD 2X1 100LFCSP
相關代理商/技術參數
參數描述
AD8151-EVAL 制造商:Analog Devices 功能描述:EVAL KIT FOR 33 17, 3.2 GBPS DGTL CROSSPOINT SWIT - Bulk
AD8151XSTZ 功能描述:IC CROSSPOINT SWITCH 制造商:analog devices inc. 系列:* 零件狀態:上次購買時間 標準包裝:1
AD8152 制造商:AD 制造商全稱:Analog Devices 功能描述:34 x 34, 3.2 Gbps Asynchronous Digital Crosspoint Switch
AD8152-EVAL 制造商:Analog Devices 功能描述:EVAL KIT FOR ASYNCH DGTL CROSSPOINT SWIT - Bulk
AD8152JBP 功能描述:IC CROSSPOINT SWIT 34X34 256BGA RoHS:否 類別:集成電路 (IC) >> 接口 - 模擬開關，多路復用器，多路分解器 系列:XStream™ 其它有關文件:STG4159 View All Specifications 標準包裝:5,000 系列:- 功能:開關 電路:1 x SPDT 導通狀態電阻:300 毫歐 電壓電源:雙電源 電壓 - 電源，單路/雙路(±):±1.65 V ~ 4.8 V 電流 - 電源:50nA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:7-WFBGA，F(xiàn)CBGA 供應商設備封裝:7-覆晶 包裝:帶卷 (TR)
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*