- 您現在的位置：買賣IC網 > PDF目錄10258 > AD7938BSUZ-6 (Analog Devices Inc)IC ADC 12BIT 8CHAN 32TQFP PDF資料下載
參數資料
| 型號： | AD7938BSUZ-6 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 5/32頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 12BIT 8CHAN 32TQFP |
| 標準包裝： | 1 |
| 位數： | 12 |
| 采樣率（每秒）： | 625k |
| 數據接口： | 并聯 |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 7.5mW |
| 電壓電源： | 單電源 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 32-TQFP |
| 供應商設備封裝： | 32-TQFP（7x7） |
| 包裝： | 托盤 |
| 輸入數目和類型： | 8 個單端，單極；4 個差分，單極；4 個偽差分，單極；7 偽差分，單極 |
| 配用： | EVAL-AD7938CBZ-ND - EVAL BOARD FOR AD7938 |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
Data Sheet
AD7938-6
Rev. C | Page 13 of 32
ON-CHIP REGISTERS
The AD7938-6 has two on-chip registers that are necessary for
the operation of the device. These are the control register, which
is used to set up different operating conditions, and the shadow
register, which is used to program the analog input channels to
be converted.
CONTROL REGISTER
The control register on the AD7938-6 is a 12-bit, write-only
register. Data is written to this register using the CS and WR
pins. The control register is shown in
and the functions
of the bits are described in
. At power-up, the default bit
settings in the control register are all 0s. When writing to the
control register between conversions, ensure that
CONVST
returns high before the write is performed.
Table 6. Control Register Bits
MSB
LSB
DB11
DB10
DB9
DB8
DB7
DB6
DB5
DB4
DB3
DB2
DB1
DB0
PM1
PM0
CODING
REF
ADD2
ADD1
ADD0
MODE1
MODE0
SHDW
SEQ
RANGE
Table 7. Control Register Bit Function Description
Bit No.
Mnemonic
Description
11, 10
PM1, PM0
Power Management Bits. These two bits are used to select the power mode of operation. The user can choose
between either normal mode or various power-down modes of operation as shown in Table 8.
9
CODING
This bit selects the output coding of the conversion result. If this bit is set to 0, the output coding is straight
(natural) binary. If this bit is set to 1, the output coding is twos complement.
8
REF
This bit selects whether the internal or external reference is used to perform the conversion. If this bit is Logic 0, an
external reference should be applied to the VREF pin. If this bit is Logic 1, the internal reference is selected. See the
Reference section.
7 to 5
ADD2 to
ADD0
These three address bits are used to either select which analog input channel is converted in the next conversion if
the sequencer is not used, or to select the final channel in a consecutive sequence when the sequencer is used as
4, 3
MODE1,
MODE0
The two mode pins select the type of analog input on the eight VIN pins. The AD7938-6 can have either eight single-
ended inputs, four fully differential inputs, four pseudo differential inputs, or seven pseudo differential inputs. See
2
SHDW
The SHDW bit in the control register is used in conjunction with the SEQ bit to control the sequencer function and
access the SHDW register. See Table 10.
1
SEQ
The SEQ bit in the control register is used in conjunction with the SHDW bit to control the sequencer function and
access the SHDW register. See Table 10.
0
RANGE
This bit selects the analog input range of the AD7938-6. If it is set to 0, then the analog input range extends from
0 V to VREF. If it is set to 1, the analog input range extends from 0 V to 2 × VREF. When this range is selected, VDD must
be 4.75 V to 5.25 V if a 2.5 V reference is used; otherwise, care must be taken to ensure that the analog input remains
within the supply rails. See the Analog Inputs section for more information.
Table 8. Power Mode Selection using the Power Management Bits in the Control Register
PM1
PM0
Mode
Description
0
Normal Mode
When operating in normal mode, all circuitry is fully powered up at all times.
0
1
Autoshutdown
When operating in autoshutdown mode, the AD7938-6 enters full shutdown mode at the end of each
conversion. In this mode, all circuitry is powered down.
1
0
Autostandby
When the AD7938-6 enters this mode, all circuitry is powered down except for the reference and reference
buffer. This mode is similar to autoshutdown mode, but it allows the part to power up in 7 μs (or 600 ns if
an external reference is used). See the Power Modes of Operation section for more information.
1
Full Shutdown
When the AD7938-6 enters this mode, all circuitry is powered down. The information in the control register
is retained.
相關PDF資料 |
PDF描述 |
|---|---|
| VI-BNW-MW-S | CONVERTER MOD DC/DC 5.5V 100W |
| VI-240-IU-S | CONVERTER MOD DC/DC 5V 200W |
| MS3102A32-9S | CONN RCPT 14POS BOX MNT W/SCKT |
| MS27474T20A35P | CONN RCPT 79POS JAM NUT W/PINS |
| MS27473E8F98SA | CONN PLUG 3POS STRAIGHT W/SCKT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7938BSUZ-6REEL7 | 功能描述:IC ADC 12BIT 8CHAN 32TQFP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 其它有關文件:TSA1204 View All Specifications 標準包裝:1 系列:- 位數:12 采樣率（每秒）:20M 數據接口:并聯 轉換器數目:2 功率耗散（最大）:155mW 電壓電源:模擬和數字 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-TQFP 供應商設備封裝:48-TQFP（7x7） 包裝:Digi-Reel® 輸入數目和類型:4 個單端，單極；2 個差分，單極 產品目錄頁面:1156 (CN2011-ZH PDF) 其它名稱:497-5435-6 |
| AD7938BSUZ-REEL7 | 功能描述:IC ADC 12BIT 8CHAN 32TQFP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
| AD7939 | 制造商:AD 制造商全稱:Analog Devices 功能描述:8-Channel, 1.5 MSPS, 12-Bit and 10-Bit Parallel ADCs with a Sequencer |
| AD7939BCP | 制造商:Analog Devices 功能描述:ADC Single SAR 1.5Msps 10-bit Parallel 32-Pin LFCSP EP |
| AD7939BCP-REEL | 制造商:Analog Devices 功能描述:ADC SGL SAR 1.5MSPS 10-BIT PARALLEL 32LFCSP EP - Tape and Reel |
發布緊急采購，3分鐘左右您將得到回復。