- 您現在的位置：買賣IC網 > PDF目錄10258 > AD7938BSUZ-6 (Analog Devices Inc)IC ADC 12BIT 8CHAN 32TQFP PDF資料下載
參數資料
| 型號： | AD7938BSUZ-6 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 19/32頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 12BIT 8CHAN 32TQFP |
| 標準包裝： | 1 |
| 位數： | 12 |
| 采樣率（每秒）： | 625k |
| 數據接口： | 并聯 |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 7.5mW |
| 電壓電源： | 單電源 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 32-TQFP |
| 供應商設備封裝： | 32-TQFP（7x7） |
| 包裝： | 托盤 |
| 輸入數目和類型： | 8 個單端，單極；4 個差分，單極；4 個偽差分，單極；7 偽差分，單極 |
| 配用： | EVAL-AD7938CBZ-ND - EVAL BOARD FOR AD7938 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
AD7938-6
Data Sheet
Rev. C | Page 26 of 32
POWER MODES OF OPERATION
The AD7938-6 has four different power modes of operation.
These modes are designed to provide flexible power
management options. Different options can be chosen to
optimize the power dissipation/throughput rate ratio for
differing applications. The mode of operation is selected by the
power management bits, PM1 and PM0, in the control register,
as detailed in Table 8. When power is first applied to the
AD7938-6 an on-chip, power-on reset circuit ensures that the
default power-up condition is normal mode.
Note that, after power-on, the track-and-hold is in hold mode
and the first rising edge of CONVST places the track-and-hold
into track mode.
Normal Mode (PM1 = PM0 = 0)
This mode is intended for the fastest throughput rate
performance. The user does not have to worry about any
power-up times associated with the AD7938-6 because it
remains fully powered up at all times. At power-on reset, this
mode is the default setting in the control register.
Autoshutdown (PM1 = 0; PM0 = 1)
In this mode of operation, the AD7938-6 automatically enters
full shutdown at the end of each conversion, which is shown at
internal circuitry on the device is powered down. The part
retains information in the control register during shutdown.
The track-and-hold also goes into hold at this point and
remains in hold as long as the device is in shutdown. The
AD7938-6 remains in shutdown mode until the next rising
edge of CONVST (see Point B in
and
). In
order to keep the device in shutdown for as long as possible,
CONVST should idle low between conversions, as shown in
. On this rising edge, the part begins to power-up and
the track-and-hold returns to track mode. The power-up time
required is 10 ms minimum regardless of whether the user is
operating with the internal or external reference. The user
should ensure that the power-up time has elapsed before
initiating a conversion.
Autostandby (PM1 = 1; PM0 = 0)
In this mode of operation, the AD7938-6 automatically enters
standby mode at the end of each conversion, which is shown as
Point A in Figure 35. When this mode is entered, all circuitry
on the AD7938-6 is powered down except for the reference and
reference buffer. The track-and-hold goes into hold at this point
also and remains in hold as long as the device is in standby. The
part remains in standby until the next rising edge of CONVST
powers up the device. The power-up time required depends on
whether the internal or external reference is used. With an
external reference, the power-up time required is a minimum of
600 ns, while when using the internal reference, the power-up
time required is a minimum of 7 μs. The user should ensure this
power-up time has elapsed before initiating another conversion
as shown in
. This rising edge of
CONVST also places
the track-and-hold back into track mode.
Full Shutdown Mode (PM1 =1; PM0 = 1)
When this mode is programmed, all circuitry on the AD7938-6
is powered down upon completion of the write operation, that
is, on the rising edge of WR. The track-and-hold enters hold
mode at this point. The part retains the information in the
control register while the part is in shutdown. The AD7938-6
remains in full shutdown mode, with the track-and-hold in
hold mode, until the power management bits (PM1 and PM0)
in the control register are changed. If a write to the control
register occurs while the part is in full shutdown mode, and the
power management bits are changed to PM0 = PM1 = 0, that is,
normal mode, the part begins to power-up on the WR rising
edge and the track-and-hold returns to track. To ensure the part
is fully powered up before a conversion is initiated, the power-
up time of 10 ms minimum should be allowed before the next
CONVST falling edge; otherwise, invalid data is read.
Note that all power-up times quoted apply with a 470 nF
capacitor on the VREFIN pin.
tPOWER-UP
1
14
BUSY
CLKIN
CONVST
04
751
-04
9
A
B
Figure 39. Autoshutdown/Autostandby Mode
相關PDF資料 |
PDF描述 |
|---|---|
| VI-BNW-MW-S | CONVERTER MOD DC/DC 5.5V 100W |
| VI-240-IU-S | CONVERTER MOD DC/DC 5V 200W |
| MS3102A32-9S | CONN RCPT 14POS BOX MNT W/SCKT |
| MS27474T20A35P | CONN RCPT 79POS JAM NUT W/PINS |
| MS27473E8F98SA | CONN PLUG 3POS STRAIGHT W/SCKT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7938BSUZ-6REEL7 | 功能描述:IC ADC 12BIT 8CHAN 32TQFP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 其它有關文件:TSA1204 View All Specifications 標準包裝:1 系列:- 位數:12 采樣率（每秒）:20M 數據接口:并聯 轉換器數目:2 功率耗散（最大）:155mW 電壓電源:模擬和數字 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-TQFP 供應商設備封裝:48-TQFP（7x7） 包裝:Digi-Reel® 輸入數目和類型:4 個單端，單極；2 個差分，單極 產品目錄頁面:1156 (CN2011-ZH PDF) 其它名稱:497-5435-6 |
| AD7938BSUZ-REEL7 | 功能描述:IC ADC 12BIT 8CHAN 32TQFP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
| AD7939 | 制造商:AD 制造商全稱:Analog Devices 功能描述:8-Channel, 1.5 MSPS, 12-Bit and 10-Bit Parallel ADCs with a Sequencer |
| AD7939BCP | 制造商:Analog Devices 功能描述:ADC Single SAR 1.5Msps 10-bit Parallel 32-Pin LFCSP EP |
| AD7939BCP-REEL | 制造商:Analog Devices 功能描述:ADC SGL SAR 1.5MSPS 10-BIT PARALLEL 32LFCSP EP - Tape and Reel |
發布緊急采購，3分鐘左右您將得到回復。