參數資料
型號： AD7920BRMZ-REEL7
廠商： Analog Devices Inc
文件頁數： 4/24頁
文件大小： 0K
描述： IC ADC 12BIT SRL 250KSPS 8MSOP
標準包裝： 1,000
位數： 12
采樣率（每秒）： 250k
數據接口： DSP，MICROWIRE?，QSPI?，串行，SPI?
轉換器數目： 1
功率耗散（最大）： 15mW
電壓電源： 單電源
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 8-TSSOP，8-MSOP（0.118"，3.00mm 寬）
供應商設備封裝： 8-MSOP
包裝： 帶卷 (TR)
輸入數目和類型： 1 個單端，單極
配用： EVAL-AD7920CBZ-ND - BOARD EVALUATION FOR AD7920
AD7910/AD7920
Rev. C | Page 12 of 24
TERMINOLOGY
Integral Nonlinearity
The maximum deviation from a straight line passing through
the endpoints of the ADC transfer function. For the AD7920
and AD7910, the endpoints of the transfer function are zero
scale, a point 1 LSB below the first code transition, and full
scale, a point 1 LSB above the last code transition.
Differential Nonlinearity
The difference between the measured and the ideal 1 LSB
change between any two adjacent codes in the ADC.
Offset Error
The deviation of the first code transition (00 . . . 000) to (00 . . . 001)
from the ideal, that is, GND + 1 LSB.
Gain Error
The deviation of the last code transition (111 . . . 110) to
(111 . . . 111) from the ideal, that is, VREF 1 LSB after the offset
error has been adjusted out.
Track-and-Hold Acquisition Time
The track-and-hold amplifier returns to track mode at the end
of conversion. Track-and-hold acquisition time is the time
required for the output of the track-and-hold amplifier to reach
its final value, within ±0.5 LSB, after the end of conversion. See
the Serial Interface section for more details.
Signal-to-(Noise + Distortion) Ratio
The measured ratio of signal-to-(noise + distortion) at the output
of the A/D converter. The signal is the rms amplitude of the
fundamental. Noise is the sum of all nonfundamental signals up
to half the sampling frequency (fS/2), excluding dc. The ratio is
dependent on the number of quantization levels in the digiti-
zation process. The more levels, the smaller the quantization
noise. The theoretical signal-to-(noise + distortion) ratio for an
ideal N-bit converter with a sine wave input is given by:
Signal-to-(Noise + Distortion) = (6.02N + 1.76) dB
Thus, for a 12-bit converter this is 74 dB, and for a 10-bit
converter this is 62 dB.
Total Unadjusted Error
A comprehensive specification that includes gain error, linearity
error, and offset error.
Total Harmonic Distortion (THD)
Total harmonic distortion is the ratio of the rms sum of
harmonics to the fundamental. It is defined as:
1
2
6
2
5
2
4
2
3
2
log
20
)
(
V
dB
THD
+
=
where:
V1 is the rms amplitude of the fundamental.
V2, V3, V4, V5, and V6 are the rms amplitudes of the second
through the sixth harmonics.
Peak Harmonic or Spurious Noise
Peak harmonic or spurious noise is the ratio of the rms value of
the next largest component in the ADC output spectrum (up to
fS/2 and excluding dc) to the rms value of the fundamental.
Normally, the value of this specification is determined by the
largest harmonic in the spectrum, but for ADCs whose
harmonics are buried in the noise floor, it is a noise peak.
Intermodulation Distortion
With inputs consisting of sine waves at two frequencies, fa and fb,
any active device with nonlinearities creates distortion products
at sum and difference frequencies of mfa ± nfb where m, n = 0, 1,
2, 3, and so on. Intermodulation distortion terms are those for
which neither m nor n are equal to zero. For example, the second-
order terms include (fa + fb) and (fa fb), while the third-order
terms include (2fa + fb), (2fa fb), (fa + 2fb), and (fa 2fb).
The AD7910/AD7920 are tested using the CCIF standard, where
two input frequencies are used (see fa and fb in the Specifications
page). In this case, the second-order terms are usually distanced in
frequency from the original sine waves, while the third-order terms
are usually at a frequency close to the input frequencies. As a result,
the second- and third-order terms are specified separately. The
calculation of the intermodulation distortion is as per the THD
specification, the ratio of the rms sum of the individual distortion
products to the rms amplitude of the sum of the fundamentals,
expressed in dB.
相關PDF資料
PDF描述
CS5511-ASZR IC ADC 16BIT INTERNAL OSC 8-SOIC
MS27497T8F98P CONN RCPT 3POS WALL MNT W/PINS
CS5510-ASZR IC ADC 16BIT EXTERNAL OSC 8-SOIC
VI-JNL-IW-B1 CONVERTER MOD DC/DC 28V 100W
VI-JNJ-IW-B1 CONVERTER MOD DC/DC 36V 100W
相關代理商/技術參數
參數描述
AD7921 制造商:AD 制造商全稱:Analog Devices 功能描述:2-Channel, 2.35 V to 5.25 V 250 kSPS, 10-/12-Bit ADCs
AD7921ARM 制造商:Analog Devices 功能描述:ADC Single SAR 250ksps 12-bit Serial 8-Pin MSOP 制造商:Rochester Electronics LLC 功能描述:DUAL 12-BIT , 250KSPS ADC I.C. - Bulk 制造商:Analog Devices 功能描述:12BIT ADC DUAL SMD 7921 MSOP8
AD7921ARM-REEL 制造商:Analog Devices 功能描述:ADC Single SAR 250ksps 12-bit Serial 8-Pin MSOP T/R 制造商:Analog Devices 功能描述:ADC SGL SAR 250KSPS 12-BIT SERL 8MSOP - Tape and Reel 制造商:Rochester Electronics LLC 功能描述:DUAL 12-BIT , 250KSPS ADC I.C. - Tape and Reel
AD7921ARM-REEL7 功能描述:IC ADC 12BIT DUAL LP 8-MSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6
AD7921ARMZ 功能描述:IC ADC 12BIT DUAL LP 8-MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*