- 您現在的位置：買賣IC網 > PDF目錄375240 > AD7877ACP-REEL (ANALOG DEVICES INC) Touch Screen Controller PDF資料下載
參數資料
| 型號： | AD7877ACP-REEL |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 消費家電 |
| 英文描述： | Touch Screen Controller |
| 中文描述： | SPECIALTY CONSUMER CIRCUIT, QCC32 |
| 封裝： | 5 X 5 MM, MO-220VHHD-2, LFCSP-32 |
| 文件頁數： | 15/44頁 |
| 文件大?。?/td> | 1002K |
| 代理商： | AD7877ACP-REEL |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁
AD7877
Rev. A | Page 15 of 44
AUX3/GPIO4
BAT1
BAT2
AUX2/GPIO3
AUX1/GPIO2
12-BIT SUCCESSIVE
APPROXIMATION ADC
9 TO 1
I/P
MUX
TEMPERATURE
SENSOR
Y–
Y+
X–
X+
V
CC
REF–
IN+
REF
INT/EXT
REF+
DUAL 3-1
MUX
X– Y– GND X+ Y+ V
REF
0
Figure 27. Analog Input Structure
The AD7877 can be set up to convert specific input channels or
to convert a sequence of channels automatically. The results of
the ADC conversions are stored in the results registers. See the
Serial Interface section for details.
When measuring the ancillary analog inputs (AUX1 to AUX3,
BAT1 and BAT2), the ADC uses the internal reference, or an
external reference applied to the V
REF
pin, and the measurement
is referred to GND.
MEASURING TOUCH SCREEN INPUTS
When measuring the touch screen inputs, it is possible to
measure using the internal (or external) reference, or to use the
touch screen excitation voltage as the reference and perform a
ratiometric, differential measurement. The differential method
is the default and is selected by clearing the SER/DFR bit
(Bit 11) in Control Register 1. The single-ended method is
selected by setting this bit.
Single-Ended Method
The single-ended method is illustrated for the Y position in
Figure 28. For the X position, the excitation voltage would be
applied to X+ and X and the voltage measured at Y+.
0
ADC
REF+
(INPUT
X+
REF–
TOUCH
SCREEN
Y+
Y–
GND
V
REF
V
CC
Figure 28. Single-Ended Conversion of Touch Screen Inputs
The voltage seen at the input to the ADC in Figure 28 is
V
IN
=
V
CC
×
YTOTAL
R
Y
R
(1)
The advantage of the single-ended method is that the touch
screen excitation voltage can be switched off once the signal has
been acquired. Because a screen can draw over 1 mA, this is a
significant consideration for a battery-powered system.
The disadvantages of the single-ended method are as follows:
It can be used only if V
CC
is close to V
REF
. If V
CC
is greater than
V
REF
, some positions on the screen are outside the range of
the ADC. If V
CC
is less than V
REF
, the full range of the ADC is
not utilized.
The ratio of V
CC
to V
REF
must be known. If V
REF
and/or V
CC
vary relative to one another, this can introduce errors.
Voltage drops across the switches can introduce errors. Touch
screens can have a total end-to-end resistance of from 200
to 900 . Taking the lowest screen resistance of 200 and a
typical switch resistance of 14 , this could reduce the appar-
ent excitation voltage to 200/228 × 100 = 87% of its actual
value. In addition, the voltage drop across the low-side switch
adds to the ADC input voltage. This introduces an offset into
the input voltage, which means that it can never reach zero.
The single-ended method is adequate for applications in which
the input device is a fairly blunt and imprecise instrument such
as a finger.
Ratiometric Method
The ratiometric method is illustrated in Figure 29. Here, the
negative input of the ADC reference is tied to Y and the
positive input is connected to Y+, so the screen excitation
voltage provides the reference for the ADC. The input of the
ADC is connected to X+ to determine the Y position.
0
ADC
REF+
INPUT
(VIA MUX)
REF–
V
CC
X+
TOUCH
SCREEN
Y+
Y–
GND
Figure 29. Ratiometric Conversion of Touch Screen Inputs
相關PDF資料 |
PDF描述 |
|---|---|
| AD7877ACP-REEL7 | Touch Screen Controller |
| AD7877ACPZ-500RL7 | Touch Screen Controller |
| AD7877ACPZ-REEL | Touch Screen Controller |
| AD7890 | 8-Channel, 12-Bit Serial, Data Acquisition System(LC2MOS 8通道12位串行DAS) |
| AD7927 | 8-Channel, 200 kSPS, 12-Bit ADC with Sequencer in 20-Lead TSSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7877ACP-REEL7 | 制造商:Analog Devices 功能描述:TOUCH SCREEN CONTROLLER |
| AD7877ACPZ | 制造商:Analog Devices 功能描述:TOUCH SCREEN CNTRLR 32LFCSP - Bulk |
| AD7877ACPZ-500RL7 | 功能描述:IC ADC 12BIT TOUCHSCREEN 32LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 觸摸屏控制器 系列:- 標準包裝:96 系列:- 類型:- 觸摸面板接口:- 輸入數/鍵:- 分辨率（位）:- 評估套件:* 數據接口:- 數據速率/采樣率 (SPS，BPS):- 電壓基準:- 電源電壓:- 電流 - 電源:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:帶卷 (TR) |
| AD7877ACPZ-REEL | 功能描述:IC ADC 12BIT TOUCHSCREEN 32LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 觸摸屏控制器 系列:- 標準包裝:96 系列:- 類型:- 觸摸面板接口:- 輸入數/鍵:- 分辨率（位）:- 評估套件:* 數據接口:- 數據速率/采樣率 (SPS，BPS):- 電壓基準:- 電源電壓:- 電流 - 電源:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:帶卷 (TR) |
| AD7877ACPZ-REEL7 | 功能描述:IC ADC 12BIT TOUCHSCREEN 32LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 觸摸屏控制器 系列:- 標準包裝:96 系列:- 類型:- 觸摸面板接口:- 輸入數/鍵:- 分辨率（位）:- 評估套件:* 數據接口:- 數據速率/采樣率 (SPS，BPS):- 電壓基準:- 電源電壓:- 電流 - 電源:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。