參數資料
型號： AD7877ACP-REEL7
廠商： ANALOG DEVICES INC
元件分類： 消費家電
英文描述： Touch Screen Controller
中文描述： SPECIALTY CONSUMER CIRCUIT, QCC32
封裝： 5 X 5 MM, MO-220VHHD-2, LFCSP-32
文件頁數： 22/44頁
文件大小： 1002K
代理商： AD7877ACP-REEL7
AD7877
STOPACQ Polarity (Control Register 2 Bit <3>)
This bit should be set according to the polarity of the signal
applied to the STOPACQ pin. If that signal is active high, that is,
no acquisitions should occur during the signal’s high period,
then the POL bit should be set to 1. If the signal is active low,
then the POL bit should be 0. The default value for POL is 0.
First Conversion Delay (Control Register 2 Bits <5:4> )
The first conversion delay (FCD) bits in Control Register 2
program a delay of 500 ns (default), 128 μs, 1.024 ms, or 8.19 ms
before the first conversion, to allow the ADC time to power up.
This delay also occurs before conversion of the X and Y
coordinate channels, to allow extra time for screen settling, and
after the last conversion in a sequence, to precharge PENIRQ. If
the signal on the STOPACQ pin is being monitored and goes
active during the FCD, it is ignored until after the FCD period.
Table 8. First Conversion Delay Selection
FCD1
FCD
Function
0
0
1 clock delay (500 ns)
0
1
256 clocks delay (128 μs)
1
0
2048 clocks delay (1.024 ms)
1
1
16,384 clocks delay (8.19 ms)
Rev. A | Page 22 of 44
Power Management (Control Register 2 Bits <7:6>)
The power management (PM) bits in Control Register 2 allow
the power management features of the ADC to be programmed.
If the PM bits are 00, the ADC is powered down permanently.
This overrides any setting of the mode bits in Control
Register 1. If the PM bits are 01, the ADC and the reference
both power down when the ADC is not converting. If the PM
bits are 10, the ADC and reference are powered up continuously.
If the PM bits are 11, the ADC, but not the reference, powers
down when the ADC is not converting.
Table 9. Power Management Selection
PM1
PM0
Function
0
0
Power down continuously (default)
0
1
Power down ADC and reference when
ADC is not converting (powers up with
FCD at start of conversion)
1
0
Powered up continuously
1
1
Power down ADC when ADC is not
converting (powers up with FCD at start
of conversion)
Acquisition Time (Control Register 2 Bits <9:8>)
The ACQ bits in Control Register 2 allow the selection of
acquisition times for the ADC of 2 μs (default), 4 μs, 8 μs, or
16 μs. The user can program the ADC with an acquisition time
suitable for the type of signal being sampled. For example,
signals with large RC time constants might require longer
acquisition times.
Table 10. Acquisition Time Selection
ACQ1
ACQ0
Function
0
0
4 clock periods (2 μs)
0
1
8 clock periods (4 μs)
1
0
16 clock periods (8 μs)
1
1
32 clock periods (16 μs)
Averaging (Control Register 2 Bits <11:10>)
Signals from touch screens can be extremely noisy. The AVG
bits in Control Register 2 allow multiple conversions to be
performed on each input channel and averaged to reduce noise.
A single conversion can be selected (no averaging), which is the
default, or 4, 8, or 16 conversions can be averaged. Only the final
averaged result is written into the results register.
Table 11. Averaging Selection
AVG1
AVG0
Function
0
0
ADC performs 1 average per channel
0
1
ADC performs 4 averages per channel
1
0
ADC performs 8 averages per channel
1
1
ADC performs 16 averages per channel
SEQUENCER REGISTERS
There are two sequencer registers on the AD7877. Sequencer
Register 0 controls the measurements performed during a slave
mode sequence. Sequencer Register 1 controls the measure-
ments performed during a master mode sequence.
To include a measurement in a slave mode or master mode
sequence, the relevant bit must be set in Sequencer Register 0 or
Sequencer Register 1. Setting Bit 11 includes a measurement on
ADC Channel 0 in the sequence, which is the Y positional
measurement. Setting Bit 10 includes a measurement on ADC
Channel 1 (X+ measurement), and so on, through Bit 1 for
Channel 10. Figure 36 illustrates the correspondence between
the bits in the sequencer registers and the various measure-
ments. Bit 0 in both sequencer registers is not used. See also the
Detailed Register Descriptions section.
0
Y+
X+
Z2
AUX
1
AUX
2
AUX
3
BAT
1
BAT
2
TEMP
1
TEMP
2
Z1
NOT
USED
11
0
Figure 36. Sequencer Register
相關PDF資料
PDF描述
AD7877ACPZ-500RL7 Touch Screen Controller
AD7877ACPZ-REEL Touch Screen Controller
AD7890 8-Channel, 12-Bit Serial, Data Acquisition System(LC2MOS 8通道12位串行DAS)
AD7927 8-Channel, 200 kSPS, 12-Bit ADC with Sequencer in 20-Lead TSSOP
AD7927BRU 8-Channel, 200 kSPS, 12-Bit ADC with Sequencer in 20-Lead TSSOP
相關代理商/技術參數
參數描述
AD7877ACPZ 制造商:Analog Devices 功能描述:TOUCH SCREEN CNTRLR 32LFCSP - Bulk
AD7877ACPZ-500RL7 功能描述:IC ADC 12BIT TOUCHSCREEN 32LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 觸摸屏控制器 系列:- 標準包裝:96 系列:- 類型:- 觸摸面板接口:- 輸入數/鍵:- 分辨率（位）:- 評估套件:* 數據接口:- 數據速率/采樣率 (SPS，BPS):- 電壓基準:- 電源電壓:- 電流 - 電源:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:帶卷 (TR)
AD7877ACPZ-REEL 功能描述:IC ADC 12BIT TOUCHSCREEN 32LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 觸摸屏控制器 系列:- 標準包裝:96 系列:- 類型:- 觸摸面板接口:- 輸入數/鍵:- 分辨率（位）:- 評估套件:* 數據接口:- 數據速率/采樣率 (SPS，BPS):- 電壓基準:- 電源電壓:- 電流 - 電源:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:帶卷 (TR)
AD7877ACPZ-REEL7 功能描述:IC ADC 12BIT TOUCHSCREEN 32LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 觸摸屏控制器 系列:- 標準包裝:96 系列:- 類型:- 觸摸面板接口:- 輸入數/鍵:- 分辨率（位）:- 評估套件:* 數據接口:- 數據速率/采樣率 (SPS，BPS):- 電壓基準:- 電源電壓:- 電流 - 電源:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:帶卷 (TR)
AD7877WACPZ-REEL7 功能描述:IC CTRLR TOUCH SCREEN 32LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 觸摸屏控制器 系列:- 標準包裝:96 系列:- 類型:- 觸摸面板接口:- 輸入數/鍵:- 分辨率（位）:- 評估套件:* 數據接口:- 數據速率/采樣率 (SPS，BPS):- 電壓基準:- 電源電壓:- 電流 - 電源:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:帶卷 (TR)
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*